Manual Husqvarna P 535HX (page 54 of 72) (English)

733796

Zoom out

Zoom in

1/72

To replace the blades

1. Lock the blade with a wooden block (A).

2. Remove the bolt (B), the washers (C) and the blade

(D).

3. Assemble the new blade with the ends that have an

angle in the direction of the cutting deck.

WARNING: Incorrect blade type can

cause objects to eject from the cutting

deck and cause serious injury. Only use

approved blades. Refer to

Technical

data on page 63

4. Attach the blade, the washer and the bolt. Tighten

the bolt with a torque of 125 Nm (12.75 kpm / 92

lbft).

To do a check of the oil level in the bevel gear

of the cutting deck

1. Park the product on a level surface.

2. Lower the cutting deck to float position.

3. Do a check of the oil level in the sight glass of the

bevel gear. The oil level must be near the mark in

the middle of the sight glass.

4. If the oil level is too low, fill with oil to the middle of

the sight glass. Refer to

Technical data on page 63

for the correct oil.

To replace the oil in the bevel gear of the

cutting deck

1. Remove the cutting deck. Refer to

To remove the

cutting deck on page 28

2. Remove the sight glass.

3. Drain the oil. Use a suction device with a plastic

hose. Make sure that the plastic hose gets the oil at

the bottom of the bevel gear.

To do a check of the parallelism of the cutting

deck

1. Do a check of the air pressure in the tires. Refer to

Tire pressure on page 51

2. Park the product on a level surface.

3. Lower the cutting deck to float position.

4. Set the adjustment lever for cutting height to the

middle position.

5. Measure the distance between the ground and the

front and rear edges of the cutting deck. The

distance is measured in 2 areas. Make sure that the

rear edge is 6–9 mm (1/4 - 3/8 in.) higher than the

front edge.

54 1262 - 004 - 04.06.2020

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna P 535HX in the language / languages: English as an attachment in your email.

The manual is 13,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna P 535HX Manual

Product: