733796
36
Zoom out
Zoom in
Previous page
1/72
Next page
3. Move the lever for the hydraulic lifting arms rearward
to fully lift the hydraulic lifting arms.
4. Turn the power key to the STOP position.
5. To increase or decrease the ground pressure,
remove the pin and the bolt and move the gas spring
to 1 of the positions.
A
B
C
D
a) Use position (A) for the lowest ground pressure.
Position (A) is used for example when a cutting
deck is attached to the product.
b) Use position (B) or (C) for increased ground
pressure.
c) Use position (D) to disengage the gas spring.
Position (D) is used for example when a snow
blade is attached to the product.
To adjust the cutting height - Combi
155
1. Park the product on level ground.
2. Apply the parking brake.
3. Move the lever for the hydraulic lifting arms rearward
to fully lift the cutting deck.
4. Turn the power key to the STOP position.
5. Remove the cutting height adjustment knob on the
side of the cutting deck.
6. Put the cutting height adjustment knob in 1 of the
holes on the adjustment plate.
Note: The cutting height is shown with the numbers
1-7. Refer to the table below.
7. Tighten the cutting height adjustment knob.
8. Do steps 5-7 on the other side of the cutting deck.
9. Remove the locking pin on the cutting height
adjustment lever in the top left corner of the cutting
deck.
10. Push the cutting height adjustment lever down and
pull the lever horizontally.
11. Put the lever in the hole with the same number as on
the adjustment plate.
Note: Make sure the same number is selected on all
3 adjustment points.
12. Attach the locking pin on the cutting height
adjustment lever.
13. Adjust the parallelism of the cutting deck. Refer to
To
adjust the parallelism of the cutting deck on page
53
.
Number Cutting height, mm/in
1 30/1.2
2 40/1.6
3 52/2
4 64/2.5
5 76/2.3
6 93/3.7
7 112/4.4
To adjust the cutting height - Combi
155 X
1. Park the product on level ground.
2. Move the lever for the hydraulic lifting arms forward
to lower the cutting deck to ground position.
3. Set the auxiliary power switch to position "1".
36 1262 - 004 - 04.06.2020
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna P 535HX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna P 535HX in the language / languages: English as an attachment in your email.

The manual is 13,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info