Manual Husqvarna CT151 (page 75 of 84) (English, German, Dutch, French, Italian, Spanish)

684097

Zoom out

Zoom in

1/84

_i_

_) (1) Bottom edge of mower

(2) Lift link adjustment nut

_)(1) Unterkante des M&hwerks

(2) Hubstangen-Stellmutter

_)(1) Extr_mit_s du carter de coupe

(2) Ecrou de r_glage du bras de suspension arri_re

(_) (1) Parte inferior de la esquina de la segadora

(2) Tuerca de ajuste del v&rillaje de levantamiento

(_)(1) Bordo inferiore del tagliaerba

(2) Dado di regolazione dell'articolazione di sollevamento

(_ (1) Onderkant van de maaimachine

(2) Bijstelmoer

SIDE-TO-SIDE ADJUSTMENT

Raise mower to highest position.

At the midpoint of both sides of mower, measure height

frombottom edge ofmower toground. Distance =A"should

be the same or within 6ram (t/4") ofeach other.

• Ifadjustment is necessary, make adjustment on one side

of mower only,

• To raise one side of mower, tighten liftlink adjustment nut

on that side.

• To lower one side of mower, loosen lift link adjustment

nut on that side.

NOTE: Three full turns of adjustment nutwill change mower

height about 1/8".

• Recheck measurements after adjusting.

@ SEITLICHE EINSTELLUNG

• Des M&hwerk auf die h6chste Position einstellen.

Auf beiden Seiten des M&hwerks inder Mitte den Abstand

von der Unterkante des M&hwerks zum Boden messen.

DerAbstand =A"solite eufden beidenSeiten umh6chstens

6 mm (1/4') veneinander abweichen,

• Falls eine Einstellung notwendigsein solite, die Einstel-

lung nur auf einer Seite des M_hwerks vornehmen.

• Um eine Seite des M&hwerks anzuheben, die Hubstan-

gen-Stellmutter auf tier jeweiligen Seite festziehen.

• Um eineSeite des M_ihwerksabzusenken, die Hubstangen

-Stellmutter auf der jeweiligen Seite 16sen,

HINWEIS: Drei voile Umdmhungen derStellmutterver&ndern

die H_he des M&hwerks um etwa 3 mm (1/8").

• Nach der Einstellung die Abst&nde erneut pr0fen

REGLAGE TRANSVERSAL

Releverle carterde coupeau maximum.

Apartirdumilieudechaqueextr6mit6slatdralesducarter

decoupe,mesurerla distancedubordducarterparrap-

portau sol.

• Ladistance(A)dolt6trelam_medesdeuxc_t_s_ 6 mm

pros.

• Si unr_glageestndcessaire,ne I'effectuerqued'unseul

c_tdense rdfdrant& rautre cStd.

Abaisser ou souleverun c6td du carter de coupe en

ajustantla positionde rdcrou de rdglagedece cStd.

REMARQUE : Atroistourscompletsde I'dcroude rdglage

correspond unevariationdelahauteurau-dessusdusol,du

carter de coupe,de 0,3cm.

• Contr61er_ nouveaula distanceau sol apres cheque

operationde rdglage.

ADJUSTE DE I_ADO A LADO

Levantela segadoraa su posici6nmdsalta.

• A mediadistanciadeambosladosde lasegadore,mida

laaitumdesdelaparteinferiordelextremodelasegadora

al suelo.Ladistancia"A"debe serla mismaodentrode

6ram(1/4")dela unaa laotra.

• Siel ajustees necesario,hagaelajusteenunladodela

segadorasolamente.

• Levanteun ladedela segadorapor apretar latuercade

ajustedelvdrillajede levantamientoen ese lado.

Bajeunladodela segadorapordesapretarlatuercade

ajustedelvdrillajede levantamientoen ese lado.

NOTA: Carlatresvueltascompletasde la tuercadeajuste

cambiard la aitura de la segadora en aproximedamente

(1/8").

• Vuelvaa revisar las medidas despu_s del adjuste.

REGOLAZIONE FIANCO A FIANCO

Alzare il tagliaerba nella posizione pi_ alta.

Sui punti centrali di entrabi i lati del tagliaerba, misurare

I'altezza dal horde inferiore del taglieerba al suolo, La

distanza "A" deve essere la stessa o diversa non piQ di

circa 6ram (1/4 di pollice).

• Se necessario, fare la regolazione su un solo lato del

tagliaerba.

• Per alzare un lato del tagliaerba, stringere il dado di

regolazione delrarticolazione di sollevamento su quel

late.

• Per abbassare un lato del tagliaerba, allentare il dado

di regolazione dell'articolazione di sollevamento su quel

lato.

NOTA: Tre girl completi del dado di regolazione cambiano

I'altezza del tagliaerba di circa 3 mm (1/8 di pollice).

• Dopo aver fatto la regolazione, ricontrollare le misura-

zioni.

LINKS/RECHTS BIJSTELLEN

Zet de maaimachine in de hoogste stand.

Meet vervolgens in het midden tussen beide zijkanten

van de maaimachine de hoogte van de onderkant van

de maaimachine tot de grond, Afstand =A" moet ofwel

hetzelfde zijn, ofwel binnen 6 mm (1/4") van elkaar lig-

gen.

Indien bijstellen nodig is, mag dit slechts aan ddn kant

van de maaimachine gebeuren.

• Draai de bi stelmoer vaster aan de kant van de maaima-

ch ned e u hoger w t nstellen.

• Draai de bijstelmoer looser aan de kant van de maaima-

chine die u lager wilt instellen.

N.B.: Drei slagen van de bijstelmoer veranderen de hoogte

ongeveer 3 mm (1/8").

• Controleer na het bijstellen de hoogte opnieuw.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna CT151 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna CT151 Manual

Product: