685907

Hunter ACC Manual

24
Zoom out
Zoom in
Previous page
1/100
Next page
17
ACC can therefore run automatic programs, manual
station and programs, and ICR commands simultaneously.
Each running event will be shown on the display with
the reason for running (programs will be shown with the
program letter followed by “ICR” if they were started by
the remote), and the remaining time for the event.
The display shown here is possible with ACC: six events
are running, including ICR station starts (ICR), ICR
program starts (A-ICR), manual single-stations (MAN),
manual program starts (C-MAN), and an automatic
program (D-AUTO).
Figure 3
If simultaneous operation is not desired, press the
Off button on ICR before starting another program or
station. Off will stop everything the controller is running,
regardless of what started it.
Stacking and SmartStack rules are not observed when
manual single station ICR commands are sent to the ACC.
Stacking and SmartStack rules do apply when manual
program ICR commands are sent to the ACC. If a program
is not set to overlap, the ICR command will be ignored
when trying to start the manual program.
ICR manual single station commands will be obeyed
if the controller is in the OFF position, or in a sensor
shutdown mode. ICR manual program commands will
NOT be obeyed and will be ignored in the OFF position. If
the controller is in a sensor shutdown mode and an ICR
command is sent to activate a program, the ACC will obey
the sensor shutdown if that program is assigned to pause
or suspend according to the sensor. The manual program
ICR command will be shown in the display as in pause or
suspend mode, depending on how you have your sensor
programmed. (Fig 3) If the program that you are trying to
manually start with an ICR command is not programmed
to pause or suspend a sensor, the command will be obeyed
and the program will run.
If you are utilizing a simultaneous station group, or SSG,
you may run an individual station that is included in the
SSG. The fact that the station is included in the SSG will be
ignored, and you may run that station by itself.
ConneCTInG To Imms .................................................................
hunTer IrrIGaTIon manaGemenT and monITorInG sysTem
ACC controllers can upgraded to provide full two-way
communications with central control software (IMMS 2.0).
The ACC Com modules are installed in place of the logo
badge on wall mount controllers, and under the facepack
door in a special bracket (APPBRKT) in pedestal units.
ACC controllers can be connected with hardwired cable
(GCBL), dial-up telephone (POTS or “plain old telephone
service”), or GSM cellular communications (using Circuit
Switched Data or CSD).
Multiple controllers can share a connection, with
additional runs of hardwired cable or UHF radio
communications. Advance to Daylight Saving and use +/-
to select YES.
No tee splices are permitted within the GCBL and all
hardwired devices must be in one single continuous wire
run.
DIAL-UP TELEPHONE (ACC-COM-POTS)
Connection must be within 6 ft (2 m) of the telephone
company connection, via standard RJ-11 jack..
IMMS 2.0 and dial-up Com modules require analog lines
with dial tone. These products do not have digital dialing
capabilities.
Dial-up must be via dedicated line. The controller will
always answer on the first ring and must not share with
fax machines or other devices.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hunter ACC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hunter ACC in the language / languages: English as an attachment in your email.

The manual is 7,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hunter ACC

Hunter ACC User Manual - German - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info