Manual Hot Spring PRODIGY - H (page 37 of 48) (English)

624653

Zoom out

Zoom in

1/48

Page 34

System Ground Terminal

GRD

IMPORTANT!

THE EXACT PHYSICAL LOCATION OF THE TERMINALS ON THE GFCI BREAKER

WILL VARY BETWEEN MANUFACTURERS. CONNECTING THE HOT WIRE TO THE

NEUTRAL TERMINAL WILL CAUSE IRREVERSIBLE DAMAGE TO THE CONTROL BOX.

** Refer to NEC 250-122 (table)

*PROVIDED WITH HOT TUB.

IMPORTANT: ALL WIRING SHOULD BE COPPER.

NOTE: The wire connections to GFCI breakers are for reference only. Always ensure the white neutral wire is connected to the load neutral of the 30 amp breaker.

MAIN SERVICE

ELECTRICAL

PANEL

230V, 50 Amp,

2-POLE,

CIRCUIT BREAKER

(NON GFCI)

FACTORY

WIRED

HEATER

L2 # 12 AWG RED

L1 # 12 AWG BLUE

L2 # 10 AWG RED

L1 # 10 AWG BLUE

N # 10 AWG WHITE

GROUND # 10 AWG GREEN

# 8 AWG WHITE, NEUTRAL

# 10 AWG GREEN, GROUND**

# 8 AWG BLUE, L1

# 8 AWG RED, L2

*SUBPANEL

WITH GFCI

BREAKERS

Minimum 5 FEET

The Subpanel must be

within sight of the spa

Do not exceed 50 FEET.

GRANDEE (GG) , ENVOY (KK), VANGUARD (Model VV) & ARIA (Model AR)

230 volt permanently connected model

electrIcal reQuIrementS

IMPORTANT

: Fill the spa with water before turning on the power.

Your HOT SPRING spa has been carefully designed to give you

maximum safety against electrical shock. Connecting the spa to an

improperly wired circuit will negate many of the spa’s safety features.

Improper wiring may also cause electrocution, risk of fire, and other

risks of injuries. Please read and follow the electrical installation

requirements and instructions for your specific spa model completely!

All HOT SPRING spa models, are equipped with a power indicator

(HOT SPRING Logo blue light) which, in addition to showing the spa

has power to it, has a diagnostic function as well. It will begin blinking

if the heater high-limit thermostat has tripped. If the power indicator

light is blinking, follow the instructions in the Troubleshooting section

to identify and correct the cause. The power indicator will stop blinking

once the problem has been corrected. The Power and Ready indicator

lights on the control panel also provide the same diagnostic function.

230 VOLT PERMANENTLY

CONNECTED MODELS

HOT SPRING spas must be wired in accordance with all applicable

local electrical codes. All electrical work should be done by an

experienced, licensed electrician. We recommend the use of

appropriate electrical conduit, fittings, and wire for all circuits.

The following two diagrams illustrate how to wire specific spa

models:

• An electrical subpanel containing two GFCI breakers is included with

each 230 volt spa. We recommend that this subpanel be used to

supply power to the spa.

• The subpanel requires a 50 amp, single phase, 230 volt, four wire

service (two line, one neutral, one ground). The grounding conductor

must not be less than #10 AWG. Refer to local codes and to NEC 250-

122 (table).

• Mount the subpanel in the vicinity of the spa, but not closer than five

feet away, in accordance with all local codes. (N.E.C. 680-38 to 41-A-3)

Once your spa has been filled with water, turn it on and test all of the

circuit breakers.

IMPORTANT: If both breakers immediately trip, verify that the wires are

correctly connected. Each breaker should be tested prior to each use.

Here’s how:

1. Push the “TEST” button on each GFCI breaker, and observe it click

OFF.

2. Wait 30 seconds, then push the breaker switch to the OFF (down)

position (to ensure that it has completely disengaged), then push the

breaker switch to the ON (up) position. If you don't wait 30 seconds,

the spa’s power indicator may continue to blink – try again.

If any of the GFCI breakers fails to operate in this manner, your spa

may have an electrical malfunction, and you may be at risk of electrical

shock. Turn off all circuits and do not use the spa until the problem has

been corrected by an authorized service agent.

WARNING: Removing, or bypassing any GFCI breaker will result

in an unsafe spa and will void the spa’s warranty.

Electrical Requirements

I have a 2001 prodigy and the circulation pump doesn’t seem to come on. And now cold weather the jets poor out very cold water. What could this be? Submitted on 18-10-2022 at 15:54
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hot Spring PRODIGY - H in the language / languages: English as an attachment in your email.

The manual is 6,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hot Spring PRODIGY - H Manual

Product: