Manual Hot Spring PRODIGY - H (page 12 of 48) (English)

624653

Zoom out

Zoom in

1/48

Page 9

FUNDAMENTALS OF

WATER MAINTENANCE

• Testing: Test the water weekly or each time the spa is used with

convenient FRESHWATER 5-way test strips or more accurate liquid/

tablet reagent test kit per instructions. Critical parameters: sanitizer

level, pH, Calcium Hardness (CH), and Total Alkalinity (TA). Store test

equipment in a dark, cool, dry place to maintain potency.

• Water Filtration: The 100% no by-pass 24 hour filtration used in HOT

SPRING spas provides the best approach to keeping water clean

by constantly circulating sanitizer and removing waste from the spa.

Regularly inspect and clean filters for peak performance.

• Chemical Balance/pH Control: It is important to adjust the primary

water parameters (Total Alkalinity, Calcium hardness, pH) into the

recommended ranges so

that they are stabilized or

balanced. Balance the

water chemistry every time

you fill the spa with new

water and then during the

life of that body of water.

Keeping the water in

balance prevents damage

by holding the pH in a

safe range and preventing

calcium scale formation

on spa equipment. A low

pH can damage metal

components whereas a

high pH can cause high levels of calcium to form scale. Your dealer

should provide a detailed water chemistry orientation soon after your

new spa is filled for the very first time.

• The following three water components must be kept in balance to avoid

damage to the spa. Do balance these components in the order they

are listed here as each will help you balance the next using a minimum

amount of chemicals.

1. Calcium Hardness (CH) – CH is the measure of the amount

of dissolved calcium in the water. Low levels can make the

water corrosive and high levels cause scale formation of spa

components. The recommended CH reading is between

50 - 150 ppm. A hardness of 50 ppm is recommended with

the ACE System. If the CH level is too low, raise it with

FRESHWATER Calcium Increaser, and if the CH level is too

high, lower it with the VANISHING ACT calcium remover per

instructions. Once in balance, the CH reading normally remains

stable until new water is added. Great care must be taken when

filling the spa from a water softener to ensure that the calcium

remains in balance and avoid damage to the spa.

2. Total Alkalinity (TA) - TA is a measure of the water’s ability to

resist changes of pH or buffer capacity. A low TA allows the pH

to fluctuate easily. The recommended TA reading is between

40 - 120 ppm. To raise the TA, use FRESHWATER pH/

Alkalinity Up (sodium hydrogen carbonate). To lower the TA, use

FRESHWATER pH/Alkalinity Down (sodium bisulfate). Once the

TA is balanced, it normally remains stable until the next drain/

refill. We recommend you check the TA reading once per month.

Raising/lowering the TA may cause the pH readings to fluctuate

widely. Ignore the pH readings on the test strip while you are

balancing the TA.

3. pH - The pH is the measure of the acidity and alkalinity.

Maintaining the proper pH level will optimize the effectiveness of

the sanitizer, preventing damage to the spa and physical discomfort

for spa users. A low pH dissipates sanitizer, causes corrosion,

and irritates spa users. A high pH level will neutralize sanitizer,

promote scaling and cloud water. The recommended pH reading

is between 7.2 - 7.6. To lower the pH level, use FRESHWATER

pH/Alkalinity Down (sodium bisulfate). To raise the pH level, use

FRESHWATER pH/Alkalinity Up (sodium carbonate).

• Water Conditioners: Spa fill water varies from location to location and

user to user, therefore it is important to consult with your dealer for an

appropriate program.

a. VANISHING ACT – High levels of calcium and some minerals

can be removed from the water with the single use VANISHING

ACT. High calcium levels can cause scale formation on the spa

equipment and shell.

b. CLEAN SCREEN pre-filter –The CLEAN SCREEN pre-flter

should be used at every fill and top-off to remove contaminants

from the fill water, especially iron, copper, and manganese. Many

water sources including well water contain high concentrations of

minerals that can cause staining of the shell and plastics.

c. Stain and Scale control – For water high in calcium and minerals,

it may be necessary to use an anti-scalant like Stain and Scale

control. As water evaporates from your spa and new water is

added, the amount of dissolved minerals like calcium, copper, iron,

and manganese will increase. (Minimize evaporation by keeping

the cover on the spa whenever possible.) High iron or copper

content in the water may produce green or brown stains on the spa.

d. Foam Inhibitors - Soap is introduced into the spa water from users’

bodies and swimming apparel and can cause the spa water to

foam when the jets are used. Low levels of calcium hardness (soft

water) can increase foaming. Although ozone and ACE can oxidize

soap residual, it may become necessary to add Foam Inhibitors

to suppress the foam. Excessive soap in the water may require a

water change to resolve.

• Oxidizers: Ozone and Monopersulfate (MPS) are oxidizers used to

prevent the buildup of contaminants, maximize sanitizer efficiency,

minimize combined chlorine, and improve water clarity. They are to be

used in conjunction with EPA registered sanitizers. The FRESHWATER

III high output ozone system uses Corona Discharge technology to

produce a high concentration of ozone which is injected into the spa

water 24 hours per day. FRESHWATER Chlorine-Free Oxidizer,

Monopersulfate (MPS) is a granular oxidizing chemical.

• Sanitizers: Maintaining the recommended residual level of an EPA

registered sanitizer at all times will decrease the occurrence of unsafe

bacteria and viruses in your spa water. The recommended Free

Available Chlorine (FAC), the amount of available chlorine sanitizer,

is 3.0-5.0 ppm. A low FAC can allow bacteria and viruses to grow

rapidly in the warm water, and a high FAC can cause discomfort to the

user’s eyes, lungs, and skin. Each sanitizer carries its own instructions

regarding how much to use and when to add it to the spa water.

Consult your dealer for their recommendations and instructions on

proper sanitizing of the spa.

a. ACE Salt Water Sanitizing System

b. EVERFRESH

Water Care System FRESHWATER Concentrated

Chlorinating Granules

c. Sodium Dichloro-s-Triazinetrione (sodium dichlor or chlorine)

d. Brominating Concentrate (one step granular bromine).

e. BaquaSpa

(please consult your BAQUASPA manual for

instructions on the use of this product).

ALKALINE

SPA

WATER

(SCALING

ZONE)

ADD pH

DECREASER

TO LOWER

ADD pH

INCREASER

TO RAISE

ACIDIC

SPA

WATER

(CORROSIVE

ZONE)

COMFORT

ZONE

IDEAL

Water Quality and Maintenance

I have a 2001 prodigy and the circulation pump doesn’t seem to come on. And now cold weather the jets poor out very cold water. What could this be? Submitted on 18-10-2022 at 15:54
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hot Spring PRODIGY - H in the language / languages: English as an attachment in your email.

The manual is 6,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hot Spring PRODIGY - H Manual

Product: