Manual Hot Spring PRODIGY - H (page 10 of 48) (English)

624653

Zoom out

Zoom in

1/48

Page 7

1. Wavemaster

jet pump

2. No-Fault

heater

3. Silent Flo 5000

circulation pump

4. IQ 2020

control box

5. Ozone injector

6. *Main drain (with shut-off valve)

7. *Secondary drain

8. Bonding terminal

EQUIPMENT COMPARTMENT

GettInG Started

EQUIPMENT COMPARTMENT

The illustration below is to be used as a reference

only (your spa may look different). The equipment

compartment is located behind the front panel of the spa

below the control panel.

Getting Started

8. ROTATE THE SMARTJET SYSTEM LEVER(S) TO THE

PRIMARY POSITION (3 O’CLOCK)

Activate the clean cycle

as described in step 5 to

turn on the CLEAN cycle for ten minutes to

circulate the spa water. After the clean cycle is complete, test the spa

water for Free Available Chlorine (FAC) residual. If the residual is

between 3 and 5 ppm on the test strips (found in the test kit) go on to

the next step. If the residual is less than 3 ppm, superchlorinate the

spa water by adding 1½ teaspoons of chlorine (sodium dichlor) per

250 gallons

(950 liters)

of spa water. Activate the clean cycle again to

circulate the spa water for another ten-minute period.

9. ROTATE THE SMARTJET SYSTEM LEVER(S) TO 2ND

POSITION

(9 O’CLOCK)

Activate the

clean cycle as

described in step 5 to

turn on the cycle for ten minutes to circulate

the spa water

. Test the spa water for Free Available Chlorine (FAC)

residual. If the residual is between 3 and 5 ppm on the test strips

(found in the test kit) go on to the next step. If the residual is less

than 3 ppm, superchlorinate the spa water by adding 1½ teaspoons

of chlorine (sodium dichlor) per 250 gallons (950 liters) of spa water.

Then

Activate the clean cycle again to circulate the spa water for

another ten-minute period.

Repeat this procedure until both

SMARTJET lever(s) operating positions have been tested.

10. RECHECK the Total Alkalinity (TA) at 80 ppm, Calcium Hardness

(CH) at 100 ppm, then spa water pH at between 7.2 and 7.6. using a

FRESHWATER 5-way test strip.

IMPORTANT: Make sure you adjust your Total Alkalinity first, as

an out-of-balance condition will affect your ability to adjust the pH

correctly, and will prevent the sanitizer from operating effectively.

The spa is ready for use when the spa water has circulated

through each SMARTJET lever operating position and the

chlorine level remains between 3 ppm and 5 ppm.

11. TEST WATER WEEKLY OR BEFORE EACH TIME

THE SPA IS USED

* This drain may be reversed with other drain depending on your spa, the Main drain will always have a shut-off valve attached.

I have a 2001 prodigy and the circulation pump doesn’t seem to come on. And now cold weather the jets poor out very cold water. What could this be? Submitted on 18-10-2022 at 15:54
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hot Spring PRODIGY - H in the language / languages: English as an attachment in your email.

The manual is 6,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hot Spring PRODIGY - H Manual

Product: