585432

Honeywell HCF 82 Manual

9
Zoom out
Zoom in
Previous page
1/32
Next page
Particular features of HCW 82
9
3. Particular features of
HCW 82
3.1. Operation
The room setpoint temperature can be set easily at the
setpoint adjuster HCW 82 by means of an adjustment dial.
The adjustment range amounts to ± 12 °C, starting from the
basic value of 20 °C (in position 0).
Fig. 5: HCW 82
► Select the desired change of the preset temperature at the
adjustment dial (1) (see Fig. 5)
(settings on the scale in °C).
3.2. Limiting the adjustment range
You can limit the setting range that can be used at the
adjustment dial.
► Remove the housing cover (see Fig. 1, Page 7).
Fig. 6: Limiting the adjustment range
► Place the two small pins into the holes of the adjustment
dials in order to limit the adjustment range (see Fig. 6).
Orientate yourself on the basis of the inner scale:
In Fig. 6, the pins are inserted so that the adjustment dial
can only be adjusted by ±3 °C around the zero point.
► Turn the adjustment dial clockwise until it stops.
► Check whether the adjustment dial is in the position shown
in Fig. 5.
► If appropriate, put the adjustment back in, rotated by 180°
until it has the position shown.
► Turn the adjustment dial to Position 0.
► Place the housing cover in position above and snap it
down (see Fig. 4).
3.3. Operation with an external power
source
In addition to battery operation, the setpoint adjuster
HCW 82 is also prepared for operation with an external
power source.
WARNING
Damage to the device!
Use of an unsuitable power supply unit.
► Use a power supply unit with 3 V DC
± 10%, min. 25 mA.
► Keep the power supply unit de-
energised while connecting it.
► Observe the connection diagram next
to the cable terminals.
► Have a power supply unit with 3 V DC ± 10 %, min. 25 mA
at hand.
► De-energise the power supply unit.
► Remove the housing cover of the HCW 82 (see Fig. 1,
Page 7).
► Remove the batteries.
Dispose of the batteries according to the
local statutory requirements and not with
the used domestic refuse.
► Unscrew the setpoint adjuster HCW 82.
2
1
12 3
+ 3V
Fig. 7: Connection of the external power source (only HCW 82)
The maximum permissible cable length from the
power supply unit to the device amounts to
100 m. If possible, use a cable of the type JE-Y
(ST)Y 2x2x0.8 mm or JE-LIYCY 2x2x0.5 mm
2
.
► Lead the outlet cable of the power supply unit through the
housing opening (1) (see Fig. 7) to the inside.
► Connect the outlet cable to the terminal (2)
(see Fig. 7).
– Connection 2: Earth
– Connection 3: Voltage
► Screw the setpoint adjuster HCW 82 back on.
► Place the housing cover in position above and snap it
down (see Fig. 4).
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell HCF 82 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell HCF 82 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info