554935
87
Zoom out
Zoom in
Previous page
1/122
Next page
79
Galaxy 2 Series Installation Manual
Option 53 - Outputs
This option allows the operation of all the system outputs to be programmed. Outputs numbered 0001 to
0008 are the outputs from the trigger header. Outputs numbered 1001 to 1004 are the standard outputs on
the main PCB. Outputs on expansion modules are shown if fitted. Each output has a sub menu containing
attributes as shown:
1. Function
Assigns the output function that activates the output.
2. Polarity
This selects if the output is normally off (positive) or normally on (negative). Positive means that the output
is 12V going to 0V when activated. Negative means that the output is 0V going to 12V when activated.
3. Groups
For output types where groups are programmable, this selects the groups that an output responds to. An
output can respond to 1, 2, 3 or 4 groups.
NOTE: Reflex means that the output stays on until the condition clears.
Latch means that the output stays on until a valid user logs on (PIN or card).
Latch* means that these outputs are latched but can be forced off by bell delay, bell time or confirm
timeouts.
Pulse means that the output stays on for five seconds and then switches off again.
4. RF Options
Option not available at present.
Selecting Outputs
On entering the option, the first output on the system is displayed; the output address, function and mode are
displayed on the top line, the polarity and assigned groups are displayed on the bottom line.
From the display of the first output, any output on the system can be displayed by pressing the A or B keys or
by entering the address of a specific output.
The output is selected for programming by pressing the ent key; the first output programming attribute
1= Function is displayed.
00=Not Used
This function is used to designate outputs that are not being used on the system.
01=Bell (Latch)
The Bells output is activated on a full alarm event when the system is set. This output is subject to the Bell
Time and Bell Delay parameters.
02=Strobe (Latch)
The Strobe output is activated on a full alarm event during the set state. This output is subject to the Bell
Delay. The Strobe output follows the Bell Time, but latches on after the last rearm.
03=Panic (Latch)
The PA output is activated whenever any of the PA zone types activate. It latches on and remains active until a
valid code, with the appropriate reset level, is entered.
53 - Outputs
87


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell Galaxy 2 Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell Galaxy 2 Series in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell Galaxy 2 Series

Honeywell Galaxy 2 Series User Manual - Dutch - 20 pages

Honeywell Galaxy 2 Series Usermanual and installation guide - Dutch - 148 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info