554935
88
Zoom out
Zoom in
Previous page
1/122
Next page
80
Galaxy 2 Series Installation Manual
04=Intruder (Latch)
The Intruder output is activated on a full alarm event during the set state.
05=Tamper (Latch)
The Tamper output is activated whenever a circuit tamper or lid tamper occurs. The output is not subject to
rearm: it latches on and remains active until a valid code, with the appropriate System Reset level, is entered.
06=24 Hour
The 24 Hour output is activated whenever a 24 Hour zone is activated. The output is not subject to rearm: it
latches on and remains active until a valid code, with the appropriate System Reset level, is entered.
08=0V Detector Reset (Pulse)
This output is always on (0V) but pulses for five seconds upon setting or system reset to reset any latching
detectors.
09=Set (Reflex)
The Set output is activated when the assigned groups on the system are set. This output is a Reflex output
and follows the set and unset status of the groups.
11=Comms Test (Pulse)
This output activates any time a test signal is sent to the Alarm Receiving Centre.
14=AC Fail (Reflex)
The AC Fail output indicates the status of the a.c. (mains) power supply. The output activates when the a.c.
supply fails or an AC Fail zone is activated. The output is reset when the a.c. supply is restored or the AC
Fail zone is closed. This output is subject to Parameter 56.7.4=Comms.Parameters.Power Delay.
15=Low Batt (Reflex)
The Low Batt output activates whenever the control unit stand-by battery falls below 10.5V or a Low Batt
zone is activated. The output is restored when the voltage rises above 10.5V or the Low Batt zone is closed.
16=Fire (Latch)
The Fire output is activated whenever a Fire zone is activated. It latches on and remains active until a valid
code (level 2 or above) is entered.
20=Confirm (Latch)
The Confirm output is activated when there have been activations on two separate zones: the second activa-
tion must occur within the Confirm Time Window. The zones do not have to be in the same group. Confirm
outputs will switch off when all groups which have been in alarm are unset.
NOTE: The Confirm output is used to give positive identification that a genuine intruder alarm condition has
occurred and to minimise the possibility of false alarm activations.
32=Omit (Reflex)
The Omit output is activated as soon as a zone is omitted from the system. The activation can be initiated
manually by omitting a zone at 11 = OMIT ZONES or by force omit at rearm. Response to either is control-
led by Option 56.7.06 = Comms.Parameters.Omit Sig.
53 - Outputs (cont’d)
88


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell Galaxy 2 Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell Galaxy 2 Series in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell Galaxy 2 Series

Honeywell Galaxy 2 Series User Manual - Dutch - 20 pages

Honeywell Galaxy 2 Series Usermanual and installation guide - Dutch - 148 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info