552645
760
Zoom out
Zoom in
Previous page
1/773
Next page
23-5
dummyheaddummyhead
IMMOBILIZER SYSTEM (HISS)
14.Disconnect the red clip of the inspection adaptor from the battery positive (+) terminal for two seconds or more, then connect it
again. The indicator remains on for approx. two seconds then it blinks four times repeatedly.
The immobilizer system (HISS) enters the registration mode. Registration of the original key used in step 4 is cancelled.
15.Turn the ignition switch OFF and remove the key.
16.Turn the ignition switch ON with a second new key. (Never use the key registered in previous step.) The indicator comes on for
two seconds then it blinks four times repeatedly.
The second key or spare key is registered in the ECM/PCM.
If there is any problem in the registration, the system will enter the diagnostic mode and the indicator will remain for approx. ten
seconds, then it will indicate the diagnostic code (page 23-7).
Keep the other transponder key away from the immobilizer receiver more than 50 mm (2.0 in).
17.Repeat the steps 15 and 16 when you continuously register the other new key.
The ECM/PCM can store up to four key codes. (The four keys can be registered.)
18.Turn the ignition switch OFF, remove the inspection adaptor and connect the CKP sensor 2P (Red) connector.
19.Turn the ignition switch ON with the registered key.
The immobilizer system (HISS) returns to the normal mode.
20.Check that the engine can be started using all registered key.
When all keys have been lost:
1. Obtain a new ECM/PCM and new key set.
2. Replace the ignition switch with a new one (page 22-24).
3. Replace the ECM/PCM with a new one (page 4-67).
4. Turn the ignition switch ON with a first new key and engine stop switch " ". The HISS indicator comes on for two seconds, then
it blinks four times repeatedly.
The first key is registered in the ECM/PCM.
If there is any problem in the registration, the system will enter the diagnostic mode and the indicator will remain for approx. ten
seconds, then it will indicate the diagnostic code (page 23-7).
5. Turn the ignition switch OFF and remove the first key.
6. Turn the ignition switch ON with a second new key. The HISS indicator comes on for two seconds, then it blinks four times
repeatedly.
The second key is registered in the ECM/PCM.
If there is any problem in the registration, the system will enter the diagnostic mode and the indicator will remain for approx. ten
seconds, then it will indicate the diagnostic code (page 23-7).
7. Turn the ignition switch OFF and remove the second key.
The system (ECM/PCM) will not enter the normal mode unless the two keys are registered in ECM/PCM.
The third new key cannot be continuously registered. When it is necessary to register the third key, follow the procedures "When
the key has been lost, or additional key is required" (page 23-3).
8. Check that the engine can be started using all registered keys.
9. Replace the remaining key set parts.
760


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda NC 700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda NC 700 in the language / languages: English as an attachment in your email.

The manual is 19,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info