720161
78
Zoom out
Zoom in
Previous page
1/112
Next page
Messages
76
Message Cause Solution
No boundary
signal
The lawnmower does not detect the
boundary wire signal.
Check if the boundary wire connectors are
correctly connected.
Check a power supply of docking station. See
“Test start points” (M page 53). If the message
does not disappear, contact your dealer.
Obstruction
detection
An obstruction is being detected. Enter the PIN so that the message disappears.
If the message does not disappear, contact your
dealer.
Obstruction
sensor
Obstruction sensor is inactive, or there
is an object interrupting the sensor.
Fully move the main cover in order to check
sensors can be activated.
Shake : Not possible to recover
Turn off : Not possible to recover
If “Obstruction sensor” message remains, check
around and underneath the cover for any objects
like chips, dust or small toys, then remove it, or
contact your dealer.
Outside loop
The lawnmower exited the boundary
wire.
Move the lawnmower into the work area.
Check the power supply of the docking station.
Check if the boundary wire connectors are
correctly connected.
If the message does not disappear, check if
the boundary wire connectors are correctly
connected, and check if there are no similar
lawnmowers in the area or any electronic device
or electrical installation that could interfere with
the lawnmower signal.
If the message still does not disappear, contact
your dealer.
Upside down
The lawnmower is upside down. Place the lawnmower on a at surface, and enter
the PIN so that the message disappears. If the
message does not disappear, contact your dealer.
Mower was
turned off
Lawnmower has been off for one
week or longer while using automatic
cutting height adjustment or automatic
seasonal timer.
Check if there are abnormalities or changes
with the condition of the lawn before resuming
operation.
Work load is too
high
The cutting height was increased
due to detection of a high work load
while using automatic cutting height
adjustment.
Check the following conditions and resume
operation.
The blades are worn out.
Dirt and cut grass have accumulated in the
working parts such as the blade disc.
The work timer has not been set for a long
enough period to mow the entire lawn.
There are obstacles such as branches and
rocks on the lawn.
Work load is too
high
Operation cannot continue due to
detection of a continuous high work
load.
Check the following conditions and resume
operation.
The blades are worn out.
Dirt and cut grass have accumulated in the
working parts such as the blade disc.
The work timer has not been set for a long
enough period to mow the entire lawn.
There are obstacles such as branches and
rocks on the lawn.
If none of the above applies, contact your dealer.
Contact your dealer if the following messages have appeared.
Area sensor
Battery Error
Battery temperature
Blade motor
Blade motor blocked
Blade motor relay
Bluetooth communication error
Charging control
Clock
Communication Error
Data memory Error
Display Unit Error
Lift sensor
Manual stop
Motor ECU Error
Motor sensor Blade
Motor sensor L
Motor sensor R
Rollover sensor
Tilt sensor
Wheel motor
Wheel motor blocked
Yaw sensor
It may be necessary to exchange the battery. Contact your dealer with the operating history ready (cutting
time, charging time, returning time).
78


Need help? Post your question in this forum.

Forumrules
1

Forum

honda-miimo-hrm3000

Reset search

  • How do I reset the password if I have forgotten it? Submitted on 11-3-2023 at 14:51

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda Miimo HRM3000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda Miimo HRM3000 in the language / languages: English as an attachment in your email.

The manual is 36,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda Miimo HRM3000

Honda Miimo HRM3000 User Manual - German - 108 pages

Honda Miimo HRM3000 User Manual - Dutch - 108 pages

Honda Miimo HRM3000 User Manual - French - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info