477992

Honda HRX426C Manual

10
Zoom out
Zoom in
Previous page
1/20
Next page
10 EN
BLADE BRAKE CABLE ADJUSTMENT
1. Stop the engine and disconnect the spark plug cap.
2. Release the flywheel brake lever [6] and verify that there is a
strong resistance when pulling on the recoil starter.
If not:
3. Measure clearance [7] at the tip of
the lever [6] = 30-35 mm.
4. If adjustment is necessary, loosen
the lock nuts [8] and adjust as
required. Tighten the lock nuts and
check the clearance again.
5. Start the engine and release the
blade brake lever. Check that the
blade and the engine stop when the
lever is released. If not, take the
mower to an approved Honda dealer.
CLUTCH CABLE ADJUSTMENT
Measure the free play [10] on the
side of lever [11] as shown.
1. Place the gear stick in the
fastest position and loosen the
locknuts [12].
1. Loosen the locknuts [12] using
a 10 mm spanner.
2. Relax or tighten the cable as
necessary so that a free play of 1 to 5
mm is achieved.
3. Retighten the locknuts [12] and
recheck the free play [10].
4. Start the engine in the open air and
operate the clutch lever. Check that the
clutch engages and disengages
correctly.
All models:
NOTE: If the clutch does not engage correctly even when the cable
is correctly adjusted, the system may need to be repaired. Take the
mower to an approved Honda dealer.
BLADE FITTING AND REMOVAL
BLADE REMOVAL
1. Place the throttle lever in “STOP”
position (Rotostop drive models).
2. Tip the mower so that the
carburetor faces upwards [13].
3. Remove the bolts [14] from the
blade [15] using a 14 mm socket
wrench [18]. Use a wood block to
stop the blade rotating when
slackening the bolts.
4. Remove the blade [15] from the blade holder [17].
NOTE:
Never tip the mower so that the carburetor faces down; this
will make starting difficult.
BLADE SHARPENING
1. Sharpen the blade cutting edges with a file. File the top side
only. Maintain the original bevel for a fine cutting edge. File both
ends evenly to maintain blade balance.
2. After sharpening, test the blade’s balance using a screwdriver
as shown. If either side dips slightly below the horizontal, file that
side. Replace the blade if it dips excessively.
CAUTION:
• To avoid weakening the blade, causing it to become unbalanced
or getting a bad quality of cut, the blade should be sharpened by
competent personnel at your Honda dealer’s.
[6]
[7]
[8]
[8]
PDE
[9]
[8]
[9]
[8]
SDE
[11]
[10]
[12]
[12]
SXE
HXE
[12]
[12]
SAFETY
D9D8D7
C18B3
[13]
[15]
[14]
[16]
[14]
[15]
[18]
[17]
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda HRX426C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda HRX426C in the language / languages: English as an attachment in your email.

The manual is 5,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda HRX426C

Honda HRX426C User Manual - German - 20 pages

Honda HRX426C User Manual - Dutch - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info