477992

Honda HRX426C Manual

9
Zoom out
Zoom in
Previous page
1/20
Next page
9 EN
CAUTION:
• The spark plug must be correctly tightened. A plug incorrectly
screwed down can become very hot and damage the engine.
MAINTENANCE OF SPARK ARRESTER
(Optional part)
(In Europe and other countries where the machinery
directive 2006/42/EC is enforced, this cleaning
should be done by your servicing dealer).
If the mower has just been run, the silencer will still be very hot.
Allow it to cool down before carrying out this operation.
In some regions, it is prohibited to operate an engine without a
spark arrester.
1. Remove the three flange
bolts [1] from the muffler
protector [2] and remove the
muffler protector.
2. Remove the two tapping
screws [3] from the spark
arrester [4] and remove the
spark arrester from the
muffler.
3. Check the carbon deposits
around the exhaust port and
spark arrester. Clean if
necessary.
4. Replace the spark arrester if
there are any breaks or
tears.
5. Install the spark arrester [4]
and muffler protector [2] in
the reverse order of removal.
THROTTLE CONTROL CABLE ADJUSTMENT
1. Place the throttle lever [5] on
“FAST” position [A] .
The arm [7] should touch the starter control [6] (clearance 0 to
1 mm).
2. If an adjustment is necessary,
loosen the lock nut of the
throttle cable and turn the
adjuster as required to obtain
the free play (0 to 1 mm).
Tighten the lock nut securely.
Place the throttle lever in the
“STARTER” position and
check whether the starter
control [6] is completely
raised.
3. Push the choke arm [8] with
your finger to check whether
it is all the way to the right.
4. Start the engine and place
the throttle lever on the
“FAST” position. Make sure it
stops when the throttle lever
is moved to the “STOP”
position.
All models:
4. Make sure the engine maximum and idle speeds are set
correctly (see chapter Technical specifications).
5. Readjust the cable if necessary.
CAUTION:
• If you do not have the required skills or equipment, it is
recommended to ask your Honda dealer for adjustment.
CARBURETOR ADJUSTMENT
1. Start the engine in the open air and allow it to reach its normal
operating temperature.
2. Place the throttle lever in “SLOW” position .
3. Screw the pilot screw [9] in or
out until you reach the
highest idle speed.
4. When the pilot screw is
correctly adjusted, turn the
throttle stop screw [10] to
obtain the specified idle
speed.
Specified idle speed: 1 700 ± 150 rpm
CAUTION:
• If you do not have the required skills or equipment, it is
recommended to ask your Honda dealer for adjustment.
BLADE CLUTCH LEVER FREE PLAY
Measure the clearance [11] at the top of the lever [3]
by holding the yellow button [12] pressed in.
It must be between 5 and 10 mm.
If necessary:
1. Undo the lock nuts [14] with a
10 mm spanner.
2. Move the nuts [14] up or
down as necessary.
3. Retighten the lock nuts [14]
and recheck the clearance.
4. Start the engine outdoors and engage the blade clutch lever.
Check that the blade starts to rotate when you pull the lever to
the rear, and that it stops rapidly when the lever is released.
If the blade does not start to rotate or stop as it should, even
when the cable is correctly adjusted, the system may need to be
repaired. Take the mower to an approved Honda dealer.
SAFETY
C18
[4]
[3]
[2]
[1]
[4]
[A]
[5]
[7]
[6]
[8]
SAFETY
C12C1
[9]
[10]
SAFETY
C16
[13]
[11]
[12]
[11]
[12]
[13]
[14]
[14]
[14]
[14]
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda HRX426C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda HRX426C in the language / languages: English as an attachment in your email.

The manual is 5,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda HRX426C

Honda HRX426C User Manual - German - 20 pages

Honda HRX426C User Manual - Dutch - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info