459023
61
Zoom out
Zoom in
Previous page
1/88
Next page
61
ENTRETIEN
MONTAGE ET DÉMONTAGE DE LAME
DÉMONTAGE DE LA LAME
1. Mettre la manette de commande des gaz sur “LENT”.
2. Tourner la clé de contact sur la position “ARRÊT”.
3. Pencher la tondeuse de façon à ce que le carburateur soit orienté vers le haut.
4. Retirer la vis [1] de la lame [2] avec une clé à douille de 14 mm. Utiliser un bloc en bois pour
empêcher la lame de tourner lors du desserrage des vis.
5. Retirer la lame [2] du porte-lame [3].
NOTE :
Ne jamais incliner la tondeuse de façon à ce que le carburateur soit orienté vers le bas ; il
en résulterait un redémarrage difficile.
AFFÛTAGE DE LA LAME
1. Affûter les bords tranchants de la lame avec une lime. N’affûter que le bord supérieur.
Conserver le biseau d’origine afin d’avoir une arête coupante très acérée. Il est recommandé
d’aiguiser les deux extrémités de manière égale, afin de maintenir l’équilibre de la lame.
2. Après l’affûtage, vérifier l’équilibre de la lame en utilisant un tournevis comme illustré. Si l’un
ou l’autre des bords penche légèrement sous l’horizontale, il faut à nouveau aiguiser ce côté.
PRÉCAUTION :
Afin d’éviter l’affaiblissement des lames, de provoquer leur déséquilibre ou d’obtenir une
coupe de mauvaise qualité, il est cependant préférable de confier l’aiguisage de la lame au
personnel compétent d’un concessionnaire agréé Honda.
MAINTENANCE
BLADE FITTING AND REMOVAL
BLADE REMOVAL
1. Place the throttle lever in “SLOW” position.
2. Install the ignition key on the “OFF” position.
3. Tip the mower so that the carburetor faces upwards.
4. Remove the bolt [1] from the blade [2] using a 14 mm socket wrench. Use a wood block to stop
the blade rotating when slackening the bolts.
5. Remove the blade [2] from the blade holder [3].
NOTE
: Never tip the mower so that the carburetor faces down; this will make starting difficult.
BLADE SHARPENING
1. Sharpen the blade cutting edges with a file. File the top side only. Maintain the original bevel
for a fine cutting edge. File both ends evenly to maintain blade balance.
2. After sharpening, test the blade’s balance using a screwdriver as shown. If either side dips
slightly below the horizontal, file that side. Replace the blade if it dips excessively.
CAUTION:
To avoid weakening the blade, causing it to become unbalanced or getting a bad quality of cut,
the blade should be sharpened by competent personnel at your Honda dealer’s.
SAFETY
C18 D7 D8
SECURITE
C18 D7 D8 D9
F
GB
D9
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda HRB475 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda HRB475 in the language / languages: English, German, French as an attachment in your email.

The manual is 1,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda HRB475

Honda HRB475 User Manual - Dutch, Italian, Spanish - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info