78945

Hitachi WF 4 DY Manual

7
Zoom out
Zoom in
Previous page
1/52
Next page
English
6
HOW TO USE THE AUTOMATIC
SCREWDRIVER
1. Operations
When you pull the switch and press the driver
straight against the workpiece in continuous
operation mode, the screw is fed and screwed in
automatically. (Fig. 17)
NOTE
⅜ Make sure that the rotation direction is correct before
the screw is tightened.
⅜ Refer to item 4 for further details of the roation
direction changeover procedures.
2. Number of screw tightenings possible
(with one charge)
Please refer to the table below for the number of
screw tightenings possible with one charge.
These values may vary slightly, according to embient
temperature and battery characteristics.
3. Tightening at a corner and adjustment operation
When the screw is tightenined, retightened or
removed in a location where the tightening is
impossible if the screw feed attachment is installed
in the main body, such as at right next to a wall
or column, remove the screw feed attachment before
operation. (Fig. 18)
4. Switch operation, changing the direction of rotation
⅜ The bit rotates clockwise (viewed from the rear side)
by pushing the R-side of the push button.
The L-side of the push button is pushed to turn the
bit counterclockwise. (See Fig. 19).
and marks are indicated on the main body.
Fig. 17
Screw used No. of tightenings
Board screw r25 Approx. 450
Board screw r41 Approx. 220
Fig. 18
NOTE:
If the tape is not set as shown in the figure, the
bit can damage the board surface (inadequate feed)
and screws can be wasted (excess feed).
2. Removal
When the screws on the tape run out or to remove
a half used belt of screws, pull the tape out in the
\ direction as shown in Fig. 16.
Slider
B section
A section
Belt guide
Collated screw
strips
(View from under)
Fig. 14
Slider
Screw
in position
Set one screw
forward.
(View from front)
Fig. 13
Fig. 12
Fig. 15
Screw mark
1 screw forward
30°
Fig. 16
Collated screw
strips
Top adjuster
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi WF 4 DY at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi WF 4 DY in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info