78945

Hitachi WF 4 DY Manual

6
Zoom out
Zoom in
Previous page
1/52
Next page
5
English
CAUTION
If the guide sleeve does not return to its original
position, then the driver bit is not installed properly.
PRIOR TO OPERATION
1. Preparing and checking the work environment
Make sure that the work site meets all the condi-
tions laid forth in the precautions.
2. Checking the battery
Make sure that the battery is installed firmly. If it
is at all loose it can drop and cause an accident.
3. Preparing the screws
Select screws appropriate to the application.
4. Bit checking and replacement
A No. 2 Plus bit is installed on this machine as a
standard accessory. Always inspect the bit to make
sure it is not damaged. Using worn bits can cause
screw-in malfunctions. Inspect the bit before work
and quickly replace it with a new one when it starts
to wear out. When the bit must be replaced due
to bit damage or any other reason, replace it
according to the instructions in Bit installation and
removal.
SCREW LENGTH AND SCREW-IN DEPTH
ADJUSTMENT
The tightening depth of this machine can be adjusted by
rotating the knob.
The tightening depth is adjusted by rotating the knob and
setting the stopper to the numerals (screw length) indicated
on the slider case.
Select a top adjuster to match screw length to be used and
attach it to the top edge. (Refer to Fig. 9)
Store the top adjuster in the storage room on the side face
of the slider case when it is not used.
The top adjuster is stored easily when the button shown in
Fig. 8 is pressed.
(1) In case that you use a screw which has a length
of 25-32 mm (L), please use the top adjuster No.
1 (small).
(2) In case that you use a screw which has a length
of 35-41 mm (L), please use the top adjuster No.
2 (large).
[Fine adjustment of tightening depth]
The tightening depth adjustments (1) to (2)
mentioned above are just preliminary.
Perform fine adjustment after trial driving.
Rotate the knob in
direction when the screw
head is too high.
Rotate the knob in direction when the screw
head is too low.
(Refer to Fig. 11)
COLLATED SCREW STRIPS INSTALLATION
AND REMOVAL
1. Installation
(1) Insert the tape tip of collated screw strips into the
belt guide groove (A section).
(2) Next, insert the tape tip into the slider groove (B
section) and feed to push in the \ direction.
(Fig. 12, Fig. 13 and Fig. 15)
(3) Set the collated tape so that the first screw is lined
up with the slider screw mark. (Fig. 14 and Fig. 15).
Driver bit
No. 2
(114L)
Anvil
hexagonal
hole
Top adjuster storage (rear side)
Fig. 8
Button
Top adjuster
No. 1 (small)
Stopper
Knob
Raise
Lower
Match the
stopper to
the screw
length
(25–32).
Fig. 9
Top adjuster
No. 2 (large)
Stopper
Knob
Fig. 10
Match the
stopper to the
screw length
(35–41).
Correct
(Flush)
Too high
Too low
Fig. 11
Fig. 7
Guide
sleeve
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi WF 4 DY at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi WF 4 DY in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info