Manual Hitachi WF 4 DY (page 5 of 52) (English, German, Dutch, French, Italian, Portuguese, Spanish)

78945

Zoom out

Zoom in

1/52

English

1. Screw feed attachment removal

Secure the main body with one hand and turn the

screw feed attachment with another hand in the

direction of the arrow mark 1 shown in Fig. 5.

Align the “@” mark of the main body and the

“#”mark of the screw feed attachment, then pull

the attachment in the direction of the arrow mark

2 shown in Fig. 6 to remove it.

NOTE

If the dust from the plaster adheres to the attachment

installation gate, it makes the attachment difficult

to remove. Clean the installation gate so the plaster

dust does not adhere.

2. Screw feed attachment installation

Perform the installation procedures in the reverse

sequence of the removal procedures.

Position the screw feed attachment over the main

body and align the “@” mark of the main body and

the “#”mark of the screw feed attachment then turn

the attachment in the direction of the “ﬁ”mark

shown in Fig. 6 to fix it.

3. Driver bit installation and removal

Collate screw tightening cannot be performed except

by the genuine driver bits for Model WF4DY.

Install the bit securely by the following procedures.

Move the guide sleeve to the top edge, insert the

bit into the hexagonal hole of the anvil and then

release the guide sleeve. (Fig. 7)

When removing the bit, perform the installation

procedures in the reverse order.

tended period is not activated, the electric discharge

might be low when using them the first and second

time. This is a temporary phenomenon, and normal

capacity will be restored by recharging the batteries

2 – 3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become com-

pletely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the

electric current, the battery may be damaged and

its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a

while.

CAUTION

⅜ If the battery has been heated just after operation

(or due to sunlight, etc.), the charger’s pilot lamp

will not light up. In such a case, first let the battery

cool, then start charging.

⅜ When the pilot lamp frickers quickly (at 0.2-second

intervals), check for and take out any foreign objects

in the charger’s battery installation hole. If there are

no foreign objects, it is probable that the battery

or charger is malfunctioning. Take it to your author-

ized Service center.

HOOK INSTALLATION

(1) Insert the hook into the A section of the main body

then turn it clockwise to set the clearance between

the housing and hook to the appropriate position.

Tighten the nut clockwise to fix the hook securely.

(Fig. 4)

(2) The hook can be hung on your belt or on a pipe

with a diameter of up to 18 mm.

SCREW FEED ATTACHMENT INSTALLATION

AND REMOVAL

CAUTION

⅜ Always make sure that the switch is turned off to

avoid an accident.

⅜ Remove the battery from the main body.

Housing

Fig. 4

Fig. 6

@ Mark

# Mark

ﬁ Mark

@ Mark

# Mark

Fig. 5

A section

Nut

Hook

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi WF 4 DY in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi WF 4 DY Manual

Product: