565914

Hitachi CL10D2 Manual

11
Zoom out
Zoom in
Previous page
1/76
Next page
English
10
3 If there is breakage or warping on the cutter edge
or if there are bulges on the cutter attachment
surface, use a file to the areas flat.
4 Use brush to remove the filings attached to the
cutter attachment groove on the bracket.
CAUTION:
As shown in Fig. 19, if the cutters are combined
in such a way that both side without the notch on
the cutter or both notch sides are facing out, the
pitch of the threads on the studs and the threads
on the cutter will not be in agreement. This can
cause damage to the cutter edge or cause wear to
premature damage to the main unit.
Fig. 19
(4) Attachment
1 When using an M6, M8 or M10 cutter
Insert the cutter in the cutter attachment groove on
the bracket, insert the special spacer between the
cutter and the bracket and then use the hex. socket
hd. bolt to tighten and secure.
2 When using the W3/8" cutter
Insert the cutter in the cutter attachment groove on
the bracket and then use the hex. socket hd. bolt
to tighten and secure.
NOTE:
Spacers are not required when using the W3/8"
cutter.
CAUTION:
The hex. socket hd. bolt should be sufficiently tightened
with the hexagonal wrench.
2. Changing the cutter attachment direction or replacing
the cutter
(1) Before removing:
1 Pull the trigger switch and move bracket (A), stopping
with the cutter in the open position.
2 Set the forward/reverse switching button to the
position (Fig. 4-2).
3 Remove the rechargeable battery from the main
unit.
(2) Removal
Use the accessory hexagonal bar wrench to remove
the hex. socket hd. bolt. It is now possible to remove
the cutter and spacer.
Fig. 16
(3) Before attaching
1 There are four edges on the cutter. As shown in
Fig. 17, by changing the position of the edge it is
possible to use the blade four times.
Fig. 17
2 There is directionality for cutter attachment in order
to change the position of the edge. Check that the
cutter has been attached so that the side without
the notch on the cutter can be seen on bracket (A)
(movable side) when seen from the main unit viewed
from the front or that the notch on the cutter
surface on bracket (B) (fixed side) can be seen (Figs.
5 and 18).
Fig. 18
1st time 2nd time 3rd time 4th time
( )
( )
Turning to
the back side
( )
Re-
insertion
( )
Turning to
the back side
Turning to
the back side
Cutter
Hex. bar wrench
Bracket (B)
Hex. socket hd. bolt
Bracket (A)
Notch side
Side without notch
DO
Both on
notch side
Both on
side without
notch
DON’T
01Eng_CL10D2_WE 1/28/08, 17:4510
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CL10D2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CL10D2 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info