565914

Hitachi CL10D2 Manual

10
Zoom out
Zoom in
Previous page
1/76
Next page
English
9
5. Removing the screw from the unit during cutting
operations
If the battery wears out during cutting operations
so that the motor stops rotating, pull the trigger
switch while pushing the forward/reverse switching
button to the side (Fig. 4-3). The motor will
rotate in the opposite direction and it will be possible
to remove the stud from the cutter (Fig. 11).
CAUTION:
䡬 When removing a stud that is suspended from
the ceiling, hold the main unit with both hands
to prevent any possibility of the stud falling.
䡬 Immediately turn off the switch once the cutter
is free from the stud. If you attempt to do this
with the switch turned on, the cutter might cut
into the stud again.
Fig. 11
6. Using the hook
The hook can be used to hang up the unit temporarily
during operations (Fig. 12).
CAUTION:
The hook should never be used to hang the unit
on your person.
When using the hook, check to make sure that the
main unit will not slip and fall, or become unstable
by the wind, etc.
Never hang the unit from your belt or trousers as
this could cause accidents.
NOTE:
During normal use or during storage, store the hook
in the latch found on the bottom of the main unit.
Fig. 12
7. Using the trimmer
NOTE: Use a special trimmer that is suitable for the
size of the stud.
If it is difficult for the nut to enter the cutting
position, either use a wrench to firmly tighten the
nut or use the accessory trimmer to remove the
flange on the screw thread.
Insert the stud in the hole on the grip. Use a pliers
to retain the stud and rotate the trimmer 5 or 6
times to the right to remove the flange and then
rotate in the opposite direction to remove the
trimmer (Fig. 13).
Fig. 13
CAUTION:
This trimmer is specially designed for Studs Cutter.
The flange on studs cut with a hacksaw or disc
grinder is too large for this trimmer so that the
trimmer does not rotate and it is not possible to
remove flange.
CUTTER LIFE AND REPLACEMENT
1. Cutter life
As is shown in Fig. 14, repeated cutting can cause
breaking and warping of the cutter edge. Using the
cutter in this condition can produce flange on the
cutting location of the studs so that the threads are
distorted. This will prevent clean cuts and make it
impossible to insert the nut.
Fig. 14
As is shown in Fig. 15, the edge is found on four
locations on the cutter. Use the method described
below to change the attachment direction of the
cutter to allow a total of four usages.
If the nut does not fit on the screw due to breaking
and warping of the edge, change the cutter
attachment direction to use the edge without
breaking and warping or replace with a new cutter.
Fig. 15
Forward/reverse
switching button
Trigger switch
Hook
Latch
Stud
Entrance
Grip
Pliers
Breaking
Warping
Four edges
on the cutter
01Eng_CL10D2_WE 1/28/08, 17:459
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CL10D2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CL10D2 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info