Manual Hitachi CL10D2 (page 9 of 76) (English, German, Dutch, French, Italian, Spanish)

565914

Zoom out

Zoom in

1/76

English

3. Cutting fixed lengths

When cutting several studs to the same length,

using the equipment in the following way will making

cutting operations more efficient.

(1) First cut one stud to the required length, and then

use it as a fixed length guide.

(2) Insert the stud used as a fixed length guide in the

stud attachment hole found on the main unit stud

guide and use the hexagonal bar wrench to tighten

and secure the hex. socket hd. bolt. Adjust at this

time so that the distance between the end of the

stud used as a fixed length and the cutter is the

necessary length.

(3) Insert the stud for cutting in the cutter, aligning the

end with that of the stud used as a cutting guide,

and then cut the stud.

Fig. 9

4. Cutting studs that are already secured

When cutting studs that are suspended from the

ceiling or secured to walls or floors.

When inserting the stud in the cutter, the meshing

of the stud thread and cutter thread is unstable. In

such a case, after inserting the stud in the cutter,

lightly pull the trigger switch to close the cutter at

low speed and then completely mesh the stud and

the upper and lower cutters. Next, pull the trigger

switch all the way to cut the stud.

CAUTION:

Use your left hand to hold the stud on the side

released by cutting to insure that it does not fall

unexpectedly.

Fig. 10

Fig. 7

1. Normal Cutting Method

(1) Pull the trigger switch and move bracket (A), stopping

with the cutter in the open position shown in Fig.

(2) As shown in Fig. 8, set the stud to be cut in the

cutter on the bracket (B) side, making sure that the

threads correctly mesh with each other.

(3) While maintaining the stud in a horizontal position,

pull the trigger switch all the way to cut the stud

(Fig. 7).

(4) After cutting turn off the switch with bracket (A)

facing directly upward. The unit stops with the

cutter in the open position, thus making it easier

to proceed to the next operation.

Fig. 8

2. Number of cuttings (per battery charging)

Refer to the chart below for the number of cuttings

per battery charging.

Table 3

Battery M10 M8 M6 W3/8"

EB1230H 550 850 1270 620

EB12B 370 570 850 410

EB12 220 340 510 250

The number of cuttings can also vary somewhat

according to the ambient temperature, characteristics

of the battery and the condition of the cutter.

Cutter

Bracket (B)

Stud

Correctly mesh

Stud

Stud attachment hole

Fixed length

guide (First cut

the stud to the

required length)

Hex. socket hd. belt

Necessary length

Stud suspended

from the ceiling

Guard section

Cutter

Stud

Bracket (B)

01Eng_CL10D2_WE 1/28/08, 17:458

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CL10D2 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi CL10D2 Manual

Product: