816356

Hikoki NT1865DBAL Manual

20
Zoom out
Zoom in
Previous page
1/420
Next page
20
English
○ Use nail strip of more than 10 nails.
○ Use an unbroken nail strip with nails of all the same
length.
The Nailer is now ready to operate.
Removing the nails:
Pull the nail feeder (B) backward. (See Fig. 12)
Return the nail feeder (B) forward quietly while pushing
the nail feeder (A).
Pull out nails from the back of the magazine. (See
Fig. 13)
<NT1850DBSL>
(1) Lightly press the stop lever and gently pull out the
magazine cover. (See Fig. 14)
(2) Set nail strip into the magazine and keep the points of
nails in contact with Groove. (See Fig. 15)
NOTE
The nails shown in page 16 can be loaded onto the side
guide groove of the magazine without any adjustment.
Always keep the points of nails in contact with Groove.
Magazine
Gap
Side guide
groove
Nail
Groove
(3) Slide the nail strip into the blade guide. (See Fig. 16)
(4) Confi rm that nail strip is placed with side guide grooves
and Groove properly, then push the magazine cover
forward to be latched.
HOW TO USE THE NAILER
WARNING
○ NEVER point tool at yourself or others in work area.
○ Keep fi ngers AWAY from trigger when not driving nails to
avoid accidental fi ring.
○ Do not use the electrical cord if damaged. Have it
repaired immediately.
○ Choice of triggering method is important.
Please read and understand “1. Nailing procedures”
found below.
○ Before starting work, check the nailing operation
switching device.
This HiKOKI nailer includes a nailing operation switching
device.
Before starting work, make sure that the switching
device is properly set.
If the switching device is not set properly, the nailer will
not operate correctly.
○ Never place your face, hands or feet near fi ring head
when using.
○ Do not drive nails on top of other nails or with Nailer at too
steep of an angle; nails can ricochet and hurt someone.
○ Do not drive nails into thin boards or near corners and
edges of workpiece. Nails can be driven through or away
from workpiece and hit someone.
○ Never drive nails from both sides of a wall at the same
time. Nails can be driven into and through the wall and
hit a person on the opposite side.
○ Never use Nailer which is defective or operating
abnormally.
○ Do not use Nailer as hammer.
○ Remove all remaining fasteners and battery from nailer
when:
1) doing maintenance and inspection;
2) checking proper operation of push lever and trigger;
3) attaching or removing the nose cap;
4) cleaning a jam;
5) it is not in use;
6) leaving work area;
7) moving it to another location; and
8) handing it to another person.
○ Remove battery from Nailer when:
1) loading nails;
2) turning the adjuster.
This HiKOKI nailer is equipped with a nailer operation
switching device.
Use FULL SEQUENTIAL ACTUATION MECHANISM or
CONTACT ACTUATION MECHANISM in accordance with
the work to be performed.
Explanation of the various nailing operations
○ FULL SEQUENTIAL ACTUATION MECHANISM:
First, press the push lever against the wood; next, pull
the trigger to drive the nail.
Follow the same sequence to continue driving nails.
After nailing once, nailing will not be possible again until
remove fi nger from the trigger and lift the tool off the
wood surface completely.
○ CONTACT ACTUATION MECHANISM:
CONTACT ACTUATION can follow two diff erent
sequences, depending on your use.
To drive several nails:
1. Pull the trigger.
2. Press the push lever against the wood to drive the
nail.
3. If the trigger is held back, a nail will be driven each
time the push lever is pressed against the wood.
To drive a single nail:
1. Press the push lever against the wood.
2. Pull the trigger to drive the nail.
3. Remove your fi nger from the trigger and remove the
nailer from the wood.
[Dry-fi re lockout mechanism]
The NT1865DBAL, NT1865DBSL and NT1865DA
employ a preventive mechanism for unloaded operation.
The NT1865DBAL, NT1865DBSL and NT1865DA enter
a state where the push lever cannot be pushed up. This
takes place when the magazine is not loaded with nails
or when the remaining number of nails becomes less
than 6 or 9.
CAUTION
Use caution not to throw the push lever tip onto wood
when the push lever cannot be pushed up.
1. Nailing procedures
This Nailer is equipped with the push lever and does not
operate unless the push lever is depressed.
There are two methods of operation to drive nails with
this Nailer.
They are:
1. Intermittent operation (Trigger fi re):
2. Continuous operation (Push lever fi re):
(1) Intermittent operation (Trigger fi re)
Use the FULL SEQUENTIAL ACTUATION MECHANISM
setting. (See Fig. 17)
WARNING
○ For intermittent operation, Set the nailing operation switch
to FULL SEQUENTIAL ACTUATION MECHANISM
(Nailing operation indicator is light in blue.) (i.e. Set to
SINGLE ACTUATION MECHANISM.)
000BookNT1865DBAL.indb20000BookNT1865DBAL.indb20 2022/06/2911:54:382022/06/2911:54:38
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki NT1865DBAL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki NT1865DBAL in the language / languages: All languages as an attachment in your email.

The manual is 38.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info