816356

Hikoki NT1865DBAL Manual

18
Zoom out
Zoom in
Previous page
1/420
Next page
18
English
NOTE
There are situations in which this product will not operate
when two LEDs are lit on the battery’s remaining battery
indicator.
This is not a malfunction but a control feature that is
specifi c to this product. The tool will operate when the
battery is recharged.
(5) Other functions
In case of operation error, LED lamps show as below.
Status of indicator
LED light
LED light blink in an interval.
• In case of too hot
condition, Blink in
1 second interval.
• In case of too cold
condition, Blink in
0.5 second interval.
After 10 seconds,
automatically turn off LED
light and Power switch.
Machine is in too cold
(below -5°C or too hot
condition.
Allow the nailer to cool
or warm-up thoroughly in
adequate condition.
2 LEDs blink in Orange,
after 10 seconds,
automatically turn off
Power switch.
Contact HiKOKI for
inspection.
(6) How to use the LED light (See Fig. 7)
While the power switch on, the LED light will automatically
light up the tip portion of the tool.
CAUTION
○ Do not expose directly your eye to the light by looking
into the light.
If your eye is continuously exposed to the light, your eye
will be hurt.
○ Wipe off any dirt or grime attached to the lens of the LED
light with a soft cloth, being careful not to scratch the
lens.
Scratches on the lens of the LED light can result in
decreased brightness.
2. Trigger Lock Mechanism (See Fig. 8)
WARNING
Make sure the trigger is locked when not fi ring nails.
This Nailer has a lock mechanism to prevent the nails
from being fi red.
Set the switch lock lever at the position to lock the
trigger.
Slide the switch lock lever to the position when the
Nailer is to be used, and to the position when it is not
in use.
BEFORE USE
Action Figure Page
Removing and inserting the
battery 22
Charging 3 3
Remaining battery indicator 28 7
Selecting accessories ―411
1. How to operate operation panel
(1) Power switch ON (See Fig. 4)
Under the condition of “Power switch OFF”, push and
hold on Power switch more than 1 second, then power
indicator lights in Green.
NOTE
Do not press the push lever and/or pull the trigger during
the process of turning the power switch ON.
Doing so will prevent the power switch from turning ON.
[Auto power off ]
When the power is turned on but the Nailer is not used
for 30 minutes, the Nailer is automatically turned off . To
turn on again, press the power switch.
WARNING
Never leave the Nailer with the power on. This could
result in an accident.
(2) Power switch OFF (See Fig. 4)
Under the condition of “Power switch ON”, push and
hold on Power switch more than 1 second, then power
indicator goes off .
Under the condition of “Power switch ON”, functions
below are active.
(3) Select Nailing operation mode
(Full sequential actuation / Contact actuation)
After power switch turn ON, always set in Full sequential
actuation mode as initial. (Nailing operation indicator
light in blue.) (See Fig. 5)
To change nailing operation mode, push Nailing
operation switch once. Every pushing, mode will change
between “Full sequential” and “Contact”. (See Fig. 6)
Lighting (Blue):
FULL SEQUENTIAL ACTUATION MECHANISM,
Blinking (Blue):
CONTACT ACTUATION MECHANISM
(4) Check Remaining battery level
When pressing the battery indicator switch, the battery
indicator shows Remaining battery level by status of LED
lamp as below.
Status of indicator
2 LEDs (Red) light
The battery remaining
power is enough.
1 LED (Red) lights
The battery remaining
power is about half.
1 LED (Red) blinks
The battery remaining
power is nearly empty.
Recharge the battery as
soon as possible.
000BookNT1865DBAL.indb18000BookNT1865DBAL.indb18 2022/06/2911:54:382022/06/2911:54:38
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki NT1865DBAL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki NT1865DBAL in the language / languages: All languages as an attachment in your email.

The manual is 38.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info