816356

Hikoki NT1865DBAL Manual

19
Zoom out
Zoom in
Previous page
1/420
Next page
19
English
3. Testing the nailer
WARNING
○ Make sure the trigger is locked when not fi ring nails.
(See Fig. 8)
○ Never use Nailer unless push lever is operating properly.
The NT1865DBAL, NT1865DBSL and NT1865DA
employ a preventive mechanism for unloaded operation.
The NT1865DBAL, NT1865DBSL and NT1865DA enter
a state where the push lever cannot be pushed up. This
takes place when the magazine is not loaded with nails
or when the remaining number of nails becomes less
than 6 or 9.
CAUTION
Use caution not to throw the push lever tip onto wood.
Before actually beginning the nailing work, test the Nailer by
using the checklist below. Conduct the tests in the following
order.
If abnormal operation occurs, stop using the Nailer and
contact a HiKOKI authorized service center immediately.
(1) REMOVE ALL NAILS AND BATTERY FROM NAILER.
□ ALL SCREWS MUST BE TIGHTENED.
□ THE PUSH LEVER AND TRIGGER MUST MOVE
SMOOTHLY with pulling back the nail feeder (B).
(NT1850DBSL: Unnecessary to pulling back nail
feeder)
(2) Installing the battery.
Do not operate the push lever or trigger while installing
the battery. (See Fig. 2)
(3) Turn on the Power switch. (See Fig. 1)
Turn on the Power switch by push and hold on Power
switch more than 1 second.
Make sure the power indicator is lighting in green, and
nailing operation indicator is lighting in blue. (FULL
SEQUENTIAL ACTUATION MECHANISM)
NOTE
Do not press the push lever and/or pull the trigger during
the process of turning the power switch ON.
Doing so will prevent the power switch from turning ON.
[Auto power off ]
When the power is turned on but the Nailer is not used
for 30 minutes, the Nailer is automatically turned off . To
turn on again, press the power switch.
WARNING
Never leave the Nailer with the power on. This could
result in an accident.
Nailing operation indicator
Lighting (Blue):
FULL SEQUENTIAL ACTUATION MECHANISM,
Blinking (Blue):
CONTACT ACTUATION MECHANISM
Make sure the battery indicator is not blinking.
If the battery indicator is blinking in red, the battery
doesn’t have enough power and it needs to be charged.
(4) Remove the fi nger from the trigger and press the push
lever against the workpiece with pulling back the nail
feeder (B).
□ THE NAILER MUST NOT OPERATE.
(5) Separate the push lever from the workpiece.
Next, point the nailer downward, with pulling back the
nail feeder (B), pull the trigger and then wait in that
position for 5 seconds or longer.
□ THE NAILER MUST NOT OPERATE.
(6) Without touching the trigger, depress the push lever
against the workpiece with pulling back the nail
feeder (B).
Next, pull the trigger.
□ THE NAILER MUST OPERATE.
Hold the trigger back and depress the push lever
against the workpiece again.
□ THE NAILER MUST NOT OPERATE.
Separate the fi nger from the trigger.
Next, is operated again.
□ THE NAILER MUST OPERATE.
(7) Separate the push lever from the workpiece, pull the
trigger.
Depress the push lever against the workpiece within
2 seconds.
□ THE NAILER MUST NOT OPERATE.
(8) Set the nailing operation indicator blinking ON mode.
(CONTACT ACTUATION MECHANISM)
Push the nailing operation switch once, make sure that
the indicator is blinking Blue.
Separate the push lever from the workpiece, pull the
trigger.
Depress the push lever against the workpiece within
2 seconds.
□ THE NAILER MUST OPERATE.
(9) If no abnormal operation is observed, you may load nails
in the Nailer.
Drive nails into the workpiece that is the same type to be
used in the actual application.
□ THE NAILER MUST OPERATE PROPERLY.
4. Checking push lever operations
WARNING
Make sure the trigger is locked when not fi ring nails.
Always make sure the trigger is locked and the battery
removed from the power tool when checking push lever
operations.
Check to make sure the push lever slides smoothly when
operated.
Clean the sliding area on the push lever if it doesn’t slide
smoothly.
5. Load nails
WARNING
When loading nails into Nailer,
1) remove battery from the nailer;
2) do not pull trigger;
3) do not depress push lever; and
4) keep nailer pointed downward.
<NT1865DBAL, NT1865DBSL, NT1865DA>
2–Action Nail Feeding!
(1) Insert nail strip into the back of the magazine. (See
Fig. 9)
(2) Slide the nail strip forward in the magazine. (See Fig. 10)
(3) Push the nail feeder (A) to engage the nail feeder (B) to
the nail strip. (See Fig. 11)
NOTE
○ Quietly push the nail feeder (A) and nail feeder (B)
against the nail.
If the nail feeder (A) and nail feeder (B) are released from
backward the magazine and bumped against the nail,
the connecting adhesive of the nail can be damaged.
000BookNT1865DBAL.indb19000BookNT1865DBAL.indb19 2022/06/2911:54:382022/06/2911:54:38
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki NT1865DBAL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki NT1865DBAL in the language / languages: All languages as an attachment in your email.

The manual is 38.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info