816399

Hikoki CR13VBY Manual

6
Zoom out
Zoom in
Previous page
1/148
Next page
6
English
2. Selection of BI-METAL blades
The BI-METAL blade numbers in Table 2 are described
on the packages of special accessories. Select
appropriate blades by referring to Table 2 and 4 below.
Table 2: Bl-METAL blades
Blade
No. Uses Thickness
(mm)
No. 101
For cutting steel and stainless pipes
less than 60 mm in outer diameter 2.5 – 6
No. 102
For cutting steel and stainless pipes
less than 130 mm in outer diameter 2.5 – 6
No. 103
For cutting steel and stainless pipes
less than 60 mm in outer diameter 2.5 – 6
No. 104
For cutting steel and stainless pipes
less than 130 mm in outer diameter 2.5 – 6
No. 105
For cutting steel and stainless pipes
less than 60 mm in outer diameter 2.5 – 6
No. 106
For cutting steel and stainless pipes
less than 130 mm in outer diameter 2.5 – 6
No. 107
For cutting steel and stainless pipes
less than 60 mm in outer diameter Below 3.5
No. 108
For cutting steel and stainless pipes
less than 130 mm in outer diameter Below 3.5
No. 121
For cutting and roughing lumber 300
No. 131
All purposes ―
No. 132
All purposes ―
NOTE
Nos. 101 – No. 132 Bl-METAL blades are sold separately as
optional accessories.
Table 3: Curved blade
Blade
No. Uses Thickness
(mm)
No. 341
For cutting steel and stainless pipes
less than 60 mm in outer diameter 2.5 – 6
3. Selection of blades for other materials
Table 4
Material to
be cut Material
quality Thickness
(mm) Blade No.
Iron plate Mild steel
plate 2.5 – 19
No. 1, 2, 101,
102, 103, 104,
105, 106, 131,
132
Below 3.5 No. 3, 107,
108
Nonferrous
metal Aluminium,
Copper and
Brass 5 – 20
No. 1, 2, 101,
102, 103, 104,
105, 106, 131
132
Below 5 No. 3, 107,
108
Synthetic
resin Phenol resin,
Melamine
resin, etc. 10 – 50 No. 1, 2, 4,
101, 102, 103,
104, 131, 132
5 – 30 No. 3, 5, 8,
105, 106, 107,
108
Vinyl chloride,
Acrylic resin,
etc. 10 – 60 No. 1, 2, 4,
101, 102, 103,
104, 131, 132
5 – 30 No. 3, 5, 8,
105, 106, 107,
108
MAINTENANCE AND INSPECTION
1. Inspecting the blade
Continued use of a dull or damaged blade will result in
reduced cutting effi ciency and may cause overloading of
the motor. Replace the blade with a new one as soon as
excessive abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes (Fig. 12)
The motor employs carbon brushes which are
consumable parts. Since an excessively worn carbon
brush can result in motor trouble, replace the carbon
brushes with new ones having the same carbon brush
No. ⓐ shown in the fi gure when it becomes worn to or
near the “wear limit” ⓑ. In addition, always keep carbon
brushes clean and ensue that they slide freely within the
brush holders.
5. Replacing carbon brushes (Fig. 12)
Disassemble the brush caps with a slotted-head
screwdriver. The carbon brushes can then be easily
removed.
6. Replacing supply cord
If the replacement of the supply cord is necessary, it
has to be done by HiKOKI Authorized Service Center to
avoid a safety hazard.
0000BookCR13VBY.indb60000BookCR13VBY.indb6 2022/02/0215:37:042022/02/0215:37:04
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CR13VBY at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CR13VBY in the language / languages: All languages as an attachment in your email.

The manual is 11.82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info