816399
4
Zoom out
Zoom in
Previous page
1/148
Next page
4
English
To maximize cutting e ciency for the materials you are
using and working conditions, adjust the speed of the
saw blade and the switching to swing cutting.
Cutting
Always hold the tool rmly with hand on housing as
shown in Fig. 9, Fig. 10 and Fig. 11.
Press the base rmly against the workpiece.
Never apply any unreasonable force to the saw blade
when cutting. Doing so can easily break the blade.
Fasten a workpiece rmly before operation. (Fig. 9)
When cutting metallic materials, use proper machine
oil (turbine oil, etc.). When not using liquid machine oil,
apply grease over the workpiece.
The service life of the saw blade will be drastically
shortened if you don’t use machine oil.
Never apply any unreasonable force to the saw blade
when cutting. Also remember to press the base against
the lumber rmly.
Sawing curved lines
We recommend that you use the BI-METAL blade
mentioned in Table 2 for the saw blade since it is tough
and hardly breaks.
Delay the feed speed when cutting the material into
small circular arcs. An unreasonably fast feed may break
the blade.
Plunge cutting (Fig. 10 and 11)
Avoid plunge cutting for metallic materials. This can
easily damage the blade.
Never pull the switch trigger while the tip of the saw
blade tip is pressed against the material. If you do so, the
blade can easily be damaged when it collides with the
material.
Make absolutely sure that you cut slowly while holding
the body rmly. If you apply any unreasonable force to
the saw blade during the cutting operation, the blade can
easily be damaged.
12. Cut o guide for cutting pipe (optional accessory)
Please refer to the cut o guide user’s manual for details
on how to use it correctly.
SYMBOLS
WARNING
The following show symbols used for the machine. Be
sure that you understand their meaning before use.
CR13VBY: Reciprocating Saw
To reduce the risk of injury, user must read
instruction manual.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2012/19/
EU on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Switching ON
Switching OFF
Straight cutting
Swing cutting
Stroke
Disconnect mains plug from electrical outlet
Class II tool
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package
contains the accessories listed in the below.
Blade (No. 341) .............................................................1
Case .............................................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
Cutting pipe and angle steel.
Cutting various lumbers.
Cutting mild steel plates, aluminum plates, and copper
plates.
Cutting synthetic resins, such as phenol resin and vinyl
chloride.
For details refer to the section entitled “SELECTION OF
BLADES”.
SPECIFICATIONS
Voltage (by areas) * (110 V, 115 V, 120 V, 127 V,
220 V, 230 V, 240 V)
Power Input * 1150 W
Capacity
Mild Steel Pipe O.D. 130 mm
Vinyl Chloride
Pipe O.D. 130 mm
Wood Depth 300 mm
Mild Steel Plate Thickness 19 mm
No-Load Speed 0 – 3000 min–1
Stroke 32 mm
Weight (without cord) ** 4,6 kg
* Be sure to check the nameplate on product as it is subject
to change by areas.
** According to EPTA-Procedure 01/2014.
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
0000BookCR13VBY.indb40000BookCR13VBY.indb4 2022/02/0215:37:042022/02/0215:37:04
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki CR13VBY at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki CR13VBY in the language / languages: All languages as an attachment in your email.

The manual is 11.82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info