700152

Hifonics x4-Boltar - Zeus Manual

20
Zoom out
Zoom in
Previous page
1/28
Next page
WHITE
BLUE
REM
BATT +12V
GND
LCH RCH
MONO BRIDGED
POWER INPUT
SPEAKER OUTPUT LOGO BADGE
FUSE
INTERCONNECTION
• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.
• Connect the front- or rear speakers with the speaker outputs (SPEAKER OUTPUT + 1CH - and + 2CH -) by using appropriate wires.
• Ensure, that the total impedance load of each speaker is not lower than 1 ohms.
Too low impedance cause high temperature and will shut down the amplifier operation.
• Always ensure the correct polarity of the speakers.
The interchange of plus and minus cause total loss of bass playback and could damage the speakers.
CROSSOVER SETTINGS
• By using bigger speakers (more than 20cm) you can set the X-OVER switch to the FULL position (Full Range Signal).
• By using smaller speakers (8.7cm - 16cm) you must set the X-OVER switch to the HP Position (Highpass Mode) to avoid damage any
by lower frequencies on the speakers. The cut-off frequency is adjustable with the HI PASS controller and should be set between
60Hz to 150Hz, depending on the size of the speakers.
• The LOW PASS and SUBSONIC Controllers are not in use in this interconnecting example.
• The push-button STEREO 12 dB / MONO 24 dB is without any purpose in this interconnecting example
LEVEL CONTROLLER
• Turn the LEVEL controller of the amplifier to the 9V position.
• Turn the volume controller of the headunit to 80 - 90% of its full setting.
• Turn the LEVEL controller clockwise until you hear some distortion.
• Then turn back the LEVEL controller slightly until you hear a cleaner sound.
BASS BOOST CONTROLLER
• The BASS BOOST controller must be turned to 0 dB position in this interconnecting example .
BASS REMOTE
• The enclosed BASS REMOTE Controller is not in use in this interconnecting example.
20
Do not connect loudspeaker cables with the vehicle chassis. Always ensure the correct polarity
of all connections. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
REFERENCE NOTE
INTERCONNECTION EXAMPLE 2-Channel Mode: Stereo 1 Front- or Rear-System
OPERATING INSTRUCTIONS
Loudspeaker left
1 – 8 Ohms
Loudspeaker right
1 – 8 Ohms
R L
Connect stereo RCA output
(R/L) of the headunit
with LINE INPUT
(R/L) of the amplifier
Switch position HP or FULL
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics x4-Boltar - Zeus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics x4-Boltar - Zeus in the language / languages: English, German as an attachment in your email.

The manual is 3,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info