700152

Hifonics x4-Boltar - Zeus Manual

21
Zoom out
Zoom in
Previous page
1/28
Next page
WHITE
BLUE
REM
BATT +12V
GND
LCH RCH
MONO BRIDGED
POWER INPUT
SPEAKER OUTPUT LOGO BADGE
FUSE
21
OPERATING INSTRUCTIONS
INTERCONNECTION
• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.
If your headunit is equipped with a additional subwoofer lineout (SUB OUT), it is recommended to use this lineout.
• Connect subwoofer 1 with the speaker output (+ LCH -) by using appropriate wires.
• Connect subwoofer 2 with the speaker output (+ RCH -) by using appropriate wires.
• Ensure, that the total impedance load of each subwoofer is not lower than 1 ohms.
Too low impedance cause high temperature and will shut down the amplifier operation.
• Always ensure the correct polarity of the speakers.
The interchange of plus and minus cause total loss of bass playback and could damage the speakers.
CROSSOVER SETTINGS
• In the mono/subwoofer mode the X-OVER switch must set to the LP/BP position (Lowpass/Bandpass mode), thereby the higher
frequencies will be eliminated. The cut-off frequency ist adjustable with the LOW PASS controller and should be set between
60 to 100 Hz, depending on the size of the subwoofer.
• The HIGH PASS controller is in this interconnection example without function.
• The SUBSONIC controller eliminates the ultra-low, not hearable and harmful frequencies and generate a bandpass signal. The subsonic
frequency should be set between 15 to 50 Hz, depending on the size of the subwoofer.
NOTE: If this value is higher than the lowpass setting, no sound is hearable.
• Push the STEREO 12 dB / MONO 24 dB push button to position MONO 24 dB, thereby the slewrate of the lowpassfilter will be advanced
to 24db/octave.
LEVEL CONTROLLER
• Turn the LEVEL controller of the amplifier to the 9V position.
• Turn the volume controller of the headunit to 80 - 90% of its full setting.
• Turn the LEVEL controller clockwise until you hear some distortion.
• Then turn back the LEVEL controller slightly until you hear a cleaner sound.
BASS BOOST CONTROLLER
• The BASS BOOST controller adjusts the bass enhancement between 0db and +18dB.
• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.
Use this controller carefully!
BASS REMOTE
• The enclosed BASS REMOTE Controller adjusts the bass-level e.g. from the driver’s seat.
Please use only this enclosed bass remote controller and cable.
• The REMOTE OUT port is suitable to connect the bass remote cable of an additional amplifier of the HiFONICS X3 or X4 Series
(only in LOW PASS-Mode). Thus to this, you are able to control two or more amplifiers with only one bass remote controller.
INTERCONNECTION EXAMPLE 2-Channel Mode: Mono with 2 Subwoofers
Subwoofer 1
1 – 8 Ohms
Subwoofer 2
1 – 8 Ohms
Connect the bass remote
controller and the remote
terminal (REMOTE IN) on
the amplifier with the
enclosed cable.
R L
Switch position LP
Switch position MONO 24 dB
Connect stereo RCA output (R/L or
SUB OUT) of the headunit with LINE
INPUT R/L of the amplifier
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics x4-Boltar - Zeus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics x4-Boltar - Zeus in the language / languages: English, German as an attachment in your email.

The manual is 3,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info