700152

Hifonics x4-Boltar - Zeus Manual

19
Zoom out
Zoom in
Previous page
1/28
Next page
19
1
The LINE INPUT RCA jacks must be connected with the RCA output jacks of the headunit.
2
The optional BALANCED INPUT is unlike the regular RCA-cables insusceptible against interspersion and interferences of the
vehicle’s electronics. You need therefor a Balanced-Line-Transmitter with a special cable, which can be connected between the
head unit and the amplifier. The Balance-Line-Transmitter is not included in delivery.
Check the further information on page 27.
Never use the Balanced-Input and the RCA-Inputs at the same time.
4
The LOW PASS controller adjusts the cut-off point of the frequency range to above. The cut-off frequency is continuously
adjustable from 40 Hz to 250 Hz.
5
The STEREO 12 dB / MONO 24 dB push button advanced the slewrate of the lowpassfilter to 24db/octave.
Switch only on 24dB, when you run the amplifier in mono-mode.
7
The HIGH PASS controller adjusts the cut-off point of the frequency range to below. The cut-off frequency is continuously
adjustable from 10 Hz to 4000 Hz (4.0 kHz).
8
The LEVEL controller adjusts the input sensitivity of the amplifier to align the audio signal from the head unit.
The input sensitivity is adjustable from 9 to 0.15 Volts.
The REMOTE IN port is for the cable of the enclosed bass remote controller and only to use in the LP/BP mode. With this bass
remote controller, you are able to adjust the bass level e.g. out of the driver’s seat. Please use only the enclosed bass remote
controller and cable.
Der REMOTE OUT port is suitable to connect the bass remote cable of an additional amplifier of the HiFONICS X3 Series (only
in LOW PASS-Mode). Thus to this, you are able to control two or more amplifiers with only one bass remote controller.
9
3
The SUBSONIC controller (Subsonicfilter) eliminates the lower frequencies of the audiosignal, to relieve the mechanical and
acoustical strain of the subwoofer and speakers. The subsonic filter is adjustable from 10 to 150 Hz.
NOTE: If this controller is turned to a higher value than the lowpass controller, no sound is hearable.
6
The X-OVER MODE switch selects the required operation mode of the amplifier.
Position LP/BP: Lowpass mode (The higher frequencies will be eliminated. Adjustable by the lowpass controller.)
Position HP: Position HP: Highpass mode (The higher frequencies will be eliminated. Adjustable by the highpass controller.)
Position FULL: Fullrange mode (the whole frequencies will be amplified). The controller LOW PASS, SUBSONIC and HIGH
PASS are without function in this mode.
VICE VERSA LINE OUTPUT SIGNAL: If you use the output signal on the LINE OUT RCAs (#12) to connect an additional amplifier,
attend in this case chapter VICE VERSA on Page 23.
10
The BASS BOOST controller adjusts the bass boost enhancement continuously from 0dB to +18dB at 45 Hz.
11
POWER/PROTECT (also featured on the bass remote controller)
If the POWER LED lights up, the amplifier is ready for operation.
If the PROTECT LED lights up, a malfunction is indicated. Attend in this case the chapter TROUBLE SHOOTING.
12
The LINE OUT RCA jacks provide a audiosignal to supply an additional amplifier.
Check the chapter VICE VERSA on Page 23.
OPERATING INSTRUCTIONS
6 7 8 91 43 5 10
FUNCTIONS AND OPERATIONAL CONTROLS
2 11 12
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics x4-Boltar - Zeus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics x4-Boltar - Zeus in the language / languages: English, German as an attachment in your email.

The manual is 3,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info