700148
21
Zoom out
Zoom in
Previous page
1/28
Next page
Switch position = LP
21
OPERATING INSTRUCTIONS
INTERCONNECTION EXAMPLE: Master/Slave Mode
MASTER/SLAVE-Mode
NOTE: The GENERATION X4 Master/SLAVE-Mode only works with two similar X4-Amplifier-Models.
INTERCONNECTION MASTER
Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.
If your headunit is equipped with a additional subwoofer lineout (SUB OUT), it is recommended to use this lineout.
Connect the remote wire (REM) to the remote terminal (REM) of the MASTER amp.
If required connect the enclosed bass remote wire only on the REMOTE IN port of the MASTER amp.
Don’t use the REMOTE OUT port in MASTER/SLAVE mode.
INTERCONNECTION SLAVE
Connect the RCA jacks SLAVE IN/OUT of the MASTER amp with the RCA jacks SLAVE IN/OUT of the SLAVE amp with appropriate
high-value RCA cables.
Connect the remote wire (REM) of the remote terminal (REM) of the MASTER amp with the remote terminal (REM) of the SLAVE amp.
Use therefore cable with a minimum profile section of 0,5 mm
2
.
• Connect the PROTECT BRIDGE port of the MASTER amp with the PROTECT BRIDGE port of the SLAVE amp with the enclosed
PROTECT BRIDGE wire.
INTERCONNECTION SUBWOOFER
• Check page 22.
SETTINGS MASTER
• The OPERATION MODE switch should be in LP position.
Please note the information of LOW PASS, SUB SONIC, PHASE, LEVEL, SUB BOOST, FREQ RANGE, Q-CONTROL and BASS
REMOTE on page 20.
SETTINGS SLAVE
• The MODE switch must be in SLAVE position.
In the SLAVE mode all controllers of the SLAVE amp are without function.
Only the already modified audiosignal of the MASTER amp will be amplified.
1. Connect Stereo RCA output (L/R or SUB OUT)
of the headunit with the LINE INPUT L/R of the
MASTER amp
Connect the bass remote controller
and the remote terminal on the
MASTER amplifier (REMOTE IN)
with the enclosed cable .
Switch position = MASTER
SLAVE
MASTER
Switch position = SLAVE
Remote wire REM Remote wire REM
Protect Bridge wire
Remote wire REM
2. Connect Stereo RCA output (MASTER OUTPUT)
of the MASTER amp with the SLAVE INPUT of the
SLAVE amp
1.
2.
Protect Bridge wire
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics X4-Atlas at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics X4-Atlas in the language / languages: English, German as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info