168839
14
Zoom out
Zoom in
Previous page
1/20
Next page
Speaker & RCA Connections
TXi 1700
LOW PASS-MODE / Subwoofer operation with lowpass
• Connect the "LINE IN" of the amplifier to the head unit´s line output with appropriate good quality RCA cables.
• Connect the subwoofer with appropriate wires to the terminal block (SPEAKER OUTPUT - and +) of the amplifier. As optional feature an
additonal subwoofer can be connected to the non-occupied terminals.
• The minimum final subwoofer impedance must not be lower than 1 Ohms in total. Too low speaker loads result in too high heat dissipation and
may cause the amplifier run into protection.
• Please observe correct speaker channels and polarity as printed by the speaker terminal.
PHASE - Control
• This controller allows to adjust the Phase Shift 0° to 180°, to match the subwoofer to the vehicle's acoustic enviroment.
FREQ RANGE - Control
Allows you to adjust the frequency at which the bass boost should work. It is continously variable between 20Hz up to 80Hz.
Q - Control
• Allows you to adjust the filter performance Q of the crossover. So you can change the playback quality in the range of the cut-off frequency.
"WIDE" Q - 0.3, "NARROW" Q - 1.0. Regular setting is on 12 o`clock - position Q - 0.5/Linkwitz-Reilly an 3 o`clock - position Q - 0.7 /Butterworth.
SUB BOOST - Control
• This controller regulates the Bass Boost from 0 - 18 dB.
Caution! Please use the Bass-EQ carefully. The additional boost may result in clipping or overload.
BASS REMOTE
• The provided Bass Remote regulates the Bass Level from e.g. the driver's seat.
MODE - Switch
• Set the switch in this operation mode to "LP" - position.
SUB SONIC - Control
• This eliminates the lowest frequencies and protects the speakers from damage. Set the frequency between 15Hz-55Hz, depending on the size of
the installed subwoofer.
NOTE: If the SUBSONIC - Level is higher than the LOW PASS - Level, no sound is hearable.
LOW PASS - Control
• This eliminates the higher frequencies. Set the crossover-frequency between 35Hz-250Hz, depending on the size of the installed subwoofer.
LEVEL - Control
• Turn the LEVEL control of the amplifier to 6V position.
• Turn the head unit volume control to about 80 - 90% of its full setting.
• Turn the LEVEL control clockwise until you hear some distortion.
• Then turn back the LEVEL control slightly until you can hear a clean sound.
Bass Remote Control - connection for remote control.
This contoller regulates the bass level from e.g. the driver's seat.
By using a additional subwoofer,
connect it to the non-occupied
terminals, ensure that the total
impedance load is not lower
than 1 Ohm.
Caution!
Do not connect speaker (-) to the ground or vehicle's chassis.
+
Subwoofer
1 - 8 Ohm
0dB 18dB
Connect RCA outputs (CH1/2 or SUB OUT) of the
head unit with LINE INPUT of the amplifier.
14
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics txi 1700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics txi 1700 in the language / languages: English, German as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info