495757

Hifonics bxi2000d Manual

19
Zoom out
Zoom in
Previous page
1/28
Next page
BXi1000D · BXi1500D · BXi2000D · BXi3000D · BXi4000D · BXi6000D
19
FUNCTIONS AND OPERATIONAL CONTROLS
MODE
BXi 4000D
1x2000 Watts
SLAVE IN/OUT
MASTERSLAVE
6 7 8 9
1
The LINE INPUT RCA jacks must be connected with the RCA output jacks of the headunit.
3
The LEVEL controller adjusts the input sensitivity of the amplifier to align the audio signal from the head unit.
The input sensitivity is adjustable from 6 to 0.2 Volts.
6
The SUB SONIC controller (Subsonicfilter) limits the ultralow and not hearable frequencies of the audiosignal to below, to avoid
a mechanical and electical overloading on the subwoofer. The cut-off frequency is adjustable from 15 to 55 Hz and depends on
the size of the subwoofer.
1 43 5
The REMOTE port is for the cable of the enclosed bass remote controller and only to use in the MASTER mode. With this bass
remote controller, you are able to adjust the bass level e.g. out of the driver’s seat. Please use only the enclosed bass remote
controller and cable.
9
2
2
The optional BALANCED INPUT is unlike the regular RCA-cables insusceptible against interspersion and interferences of the
vehicle’s electronics. You need therefor a Balanced-Line-Transmitter with a special cable, which can be connected between the
head unit and the amplifier. The Balance-Line-Transmitter is not included in delivery. Attend therefor the further information
on page 27. Never use the Balanced-Input and the RCA-Inputs at the same time.
4
The PHASE controller allows to adjust the phasing between 0° and 180°. Thereby you are able to adjust the subwoofer
perfect to the vehicle’s acustics.
5
The EXTENDED BASS CONTROL controllers allow a extensive adjustment of the bass frequencies.
The SUB BOOST controller defines the bass bosst from 0 to 18dB.
With the FREQ RANGE controller you are able to adjust, on which frequency the bass boost (SUB BOOST) is effictive.
The range goes from 20 to 80 Hz.
With the Q CONTROL controller defines the Q-Factor of the crossover continuously, so that the playback quality of the cut-off
frequency can be adjusted. Thereby you are able to adjust perfect transitions between the loudspeakers.
• WIDE equates a Q-Factor of Q 0,3 (arrow left below) = very wide frequency range.
• NARROW equates a Q-Factor of Q 1,0 (arrow right below) = very narrow frequency range.
• Q 0,5 / LINKWITZ-REILLY is the standard-setting, this means the arrow points up (12 o’clock position).
POWER/PROTECT
If the POWER LED lights up, the amplifier is ready for operation.
If the PROTECT LED lights up, a malfunction is indicated. Attend in this case the chapter TROUBLE SHOOTING.
10
The MODE switch selects the required operation mode of the amplifier.
In the SLAVE-Mode the amplifier works as a SLAVE amp, this means only the audiosignal of the MASTER amp will be amplified.
All controllers on the SLAVE Amp are without function and will be assumed by the MASTER amp.
In the MASTER-Mode (Low Pass mode) you are able to limit the frequencies to above with the LOW PASS controller. All controllers
are active. NOTE: By using only one amplifier, the Mode-Switch must set to the position MASTER.
7
The LOW PASS controller adjusts the cut-off point of the frequency range to above. The cut-off frequency is
continuously adjustable from 35 Hz to 250 Hz.
8
10 11
11
The SLAVE IN/OUT RCA jacks are suitable to connect an additional amplifier in MASTER/SLAVE mode.
Attend therefor the chapter Interconnection Example: MASTER/SLAVE on page 21.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics bxi2000d at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics bxi2000d in the language / languages: English, German as an attachment in your email.

The manual is 7,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info