495757
26
Zoom out
Zoom in
Previous page
1/28
Next page
TROUBLE SHOOTING
26
PROTECTION CIRCUIT
This amplifier owns a protection circuit. If overloading, overheating and shorted loudspeakers, or too low impedance
or insufficient power supply is insisted, the amplifier shuts down to prevent serious damage. If one of this disfunctions
is detected, the red PROTECT LED lights up.
Check in this case all connections to detect short-circuits, faulty connections or overheating. Attend the regarding notes
on the previous page.
If the reason for the disfunction is eliminated, the amplifier is ready for operation again.
If the red PROTECT LED does not stop to light up, a damage on the amplifier is insisted. In this case return the amplifier
to your car audio retailer with a detailled malfunction description and a copy of the proof of purchase.
WARNING: Never open the amplifier and try to repair it by yourself. This causes a loss of warranty. The repairing
service should be made only by skilled technicians.
REFERENCE NOTE
ELECTRICAL INTERFERENCES
The reason for interferences are mostly the passed cables and wires. Especially the power and audio cables (RCA)
of your sound system are vulnerable. Often these interferences are caused by electric generators or other electrical
units (fuel pump, A/C etc.) of the car. The most of these problems can be prevented by a correct and careful wiring.
Here are some courtesy notes:
1. Use only double or triple shielded audio RCA cables for the connection between the amplifier and headunit. A useful
alternative are represented by anti-noise-devices or additional ancillary equipment like Balanced Line Transimtters,
which you can purchase at your car audio retailer. If possible do not anti-noise-filters, which are splicing the ground
of the RCA audio cables.
2. Do not lead the audio cables between the headunit and the amplifier together with the power supply wires on the
same side of the vehicle. The best is a areal separated installation in the left and right cable channel of the vehicle.
Therewith a overlap of interferences on the audio signal will be avoided. This stands also for the equipped bass-
remote wire, which should be installed not together with the power supply wires, but rather with the audio signal
cables.
3. Avoid ground loops by connecting all ground connections in a starlike arrangement. The suitable ground center
point is ascertainable by measuring of the voltage directly on the vehicle’s battery by a multi-meter. You should
measure the voltage with turned-on inginition (acc.) and with other turned-on power consumers (e.g. headlights, rear
window defroster, etc,).Compare the measured value with the voltage of the ground point you have choosen for the
installation and the positive pole (+12V) of the amplifier. If the voltage has just a little difference, you have found a
suitable ground point. Otherwise you need to choose a other ground point.
4. Use if possible only cables with added or soldered cable sockets or the like. Gold plated or high value nickel plated
cable sockets are corrosionfree and own a very low contact resistance.
REFERENCE NOTE
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics bxi2000d at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics bxi2000d in the language / languages: English, German as an attachment in your email.

The manual is 7,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info