495757
18
Zoom out
Zoom in
Previous page
1/28
Next page
INSTALLATION INSTRUCTION
18
ELECTRICAL INTERCONNECTION
Installation of RCA/Audio signal cables and power supply.
Attend while installation not to lead the audio cables between the headunit and the amplifier together with
the power supply wires on the same side of the vehicle. The best is a areal separated installation in the
left and right cable channel of the vehicle. Therewith a overlap of interferences on the audio signal will be
avoided. This stands also for the equipped bass-remote wire, which should be installed not together with
the power supply wires, but rather with the audio signal cables.
REFERENCE NOTE
FUSE
The inserted fuses protect the amplifier from shorts and capacity overload. Replace damaged fuses only with equal fuses with
the same fuserating (attend the specifications).
NOTE: The BXi4000D model has due to construction-conditioned reasons no internal fuse-protection.
The amplifier must be fused by any means with an external In-Line-Fuse with a value of 200 A.
NOTE: The BXi6000D model has due to construction-conditioned reasons no internal fuse-protection.
The amplifier must be fused by any means with an external In-Line-Fuse with a value of 300 A.
BATT+12V
Connect the BATT+12V-terminal with the +12V pole of the vehicle’s battery. Use therefor a suitable cable with a sufficient cross
section (at least 25 mm
2
or 35 mm
2
) and install a additional in-line fuse. For safety reasons the distance between the fuseblock
and the battery must be shorter than 30 cm. Do not install the fuse into the fuseblock until the installation is accomplished.
REM
Connect the turn-on signal (e.g. automatic antenna) or the turn-on remote signal of your headunit with the REM-terminal of the
amplifier. Use therefor a suitable cable with a sufficient cross section (0,5 mm
2
). Thereby the amplifier will turn on or off automatically
with your headunit.
GND
Connect this GROUND terminal with a suitable contact ground point on the vehicle’s chassis. The ground wire must be as short
as possible and must be connected to a blank metallic point at the vehicle’s chassis. Ensure that this ground point has a stable
and safe electric connection to the negative “–”pole of the battery. Check this ground wire from the battery to the ground point if
possible and enforce it, if required. Use a ground wire with a sufficient cross section (at least 25 mm
2
or 35 mm
2
) and the same
size like the plus (+12V) power supply wire.
LOGO BADGE
This switch changes the illumination color of the upper logo badge (blue or white). Attend by any means the directives of your
national road traffic regulations.
PROTECT BRIDGE (Not on BXi6000D)
If you would like to operate two similar amplifiers in the MASTER/SLAVE mode, connect both amplifiers with the appropriate
enclosed cable on the PROTECT BRIDGE port of each amplifier. This connection ensures in case of a malfunction or a defect
on one of the amplifiers (Master or Slave), that both amplifiers will run into the protection mode and shut down.
1
2
3
4
5
BEFORE THE CONNECTION
For the professional installation of a sound system appropriate wiring kits are available in car audio retailer stores. Attend the sufficient
profile section (BXi1000D/BXi1500D/BXi2000/BXi3000D at least 25 mm
2
, BXi4000D/BXi6000D at least 35 mm
2
), the suitable fuse rating
and the conductivity of the cables when you purchase your wiring kit. Clean and remove rust-streaked and oxidized areas on the contact
points of the battery and the ground connection. Make sure that all screws are fixed tight after the installation, because loosely connections
may cause malfunctions, insufficient power supply or interferences.
6
PROTECT
BRIDGE
WHITE
LOGO
BADGE
BLUE
FUSE
GNDBATT +12V REM
SPEAKER OUTPUT
+ +
POWER INPUT
3 541 2 6
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics bxi2000d at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics bxi2000d in the language / languages: English, German as an attachment in your email.

The manual is 7,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info