Manual Hendi 230442 (page 11 of 144) (English, German, Dutch, French, Italian, Polish)

742508

Zoom out

Zoom in

1/144

# Function Description

11 down moving to next option

12 up moving to previous option

13 capital letter D (day) informs that the digital indication is in days

14 capital letter H informs that the digital indication is in hours

15 capital letter M informs that the digital indication is in minutes Colour strips are lit on the left

side of the display during water treatment. The number of current operation

cycle (description below) and the time remaining are displayed during

regeneration

symbol m3/gal/L informs that the digital indication is in cubic meters (1 cubic metre = 1000 litres)/

gallons/litres

Functions of buttons in programming moda (230459 only)

After the programming mode is entered into, the

following functions are assigned to buttons:

• Enter [9]: this button is used to activate and

conﬁrm (after setting) the changed value. After

activation, the active value (currently changed)

blinks alongside the regulation symbol [8]. Now

this value can be changed. After the set value is

conﬁrmed with enter [9], the regulation symbol

[8] will stop blinking, whereas the controller will

conﬁrm the change with a short sound signal;

• Regeneration [10]: leaving the programming

mode or changing values and moving to the pre-

vious mode of the controller;

• Down [11] changing the type of parameter to be

programmed or reducing the active value;

• Up [12] changing the type of parameter to be pro-

grammed or increasing the active value.

NOTE: Operation cycles time 2-5 is always pre-programmed adequately to the type and

quantity of resin in the container and the size of brine tank. The quantity of treated wa

ter was determined on the basis of the results of water examination delivered by You or

average values. A potential correction of these parameters shall be consulted with the

delivered of the device.

In the event of a power supply failure, the controller is equipped with a feature to store the

programmed parameters (including the current time) for 7 days.

Programming of the control head (230459 Model)

The programming mode is activated with the en-

ter [9] button. If the keypad is locked and the key

symbol is displayed, buttons must be unlocked be-

forehand by pressing for 5 seconds the down [11]

and up [12] buttons simultaneously. The regulation

symbol [8] lit indicates active mode of program-

ming settings. The regeneration symbol [10] clos-

es the programming mode. The mode will also be

closed automatically and the keypad will be locked

after 1 minute of inactivity.

A change of the displayed parameter can be done

with the down [11] button. Parameters to be pro-

grammed, the sequence of displaying:

• Current time (24-hour mode)

• The time of initiating the regeneration

• Number of days between regenerations eg.

1-02D (regeneration every 2 days)

• (2) Back wash - time of back wash in minutes.

E.G., 2 - 10M time of the 2nd cycle of operation is

10 minutes (m - indication in minutes)

• (3) Regeneration - time of regeneration and slow

rinse. E.G., 3 - 60M time of the 3nd cycle of op-

eration is 60 minutes (m - indication in minutes)

• (4) Brine reﬁll - time of ﬁlling the brine tank. E.G.,

4 - 05M time of the 4th cycle of operation is 5

minutes (m - indication in minutes)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 230442 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 1,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hendi 230442 Manual

Product: