Manual Hendi 230442 (page 7 of 144) (English, German, Dutch, French, Italian, Polish)

742508

Zoom out

Zoom in

1/144

Before first switch-on

For safety reasons, it is recommended that the wa-

ter installation of the device is vented before the

ﬁrst switch-on. In order to do so, water inlet to the

softener must be shut off. Consecutively, the sam-

pler valve after the water softener must be opened,

whereas the mains valve of the building shall be

opened gently. Water ﬂowing will push air out

through the open sampler valve. A bubbling sound

will appear and water may gush. One shall wait un-

til the ﬂow of water stabilizes and then close the

sampler valve. The system is now vented.

Venting. Filling water into the device

In order to vent the device, the sampler valve after

the water softener must be opened, whereas the

mains valve of the building shall be opened gently.

Then, one shall proceed as in the case of venting

the entire system. It is recommended that the de-

vice is ﬁlled with water gradually, with breaks, in

order not to increase pressure inside the device

abruptly.

ATTENTION! The salt tank must be ﬁlled with salt and water before the ﬁrst switch-on of

the device. One shall wait 30 minutes before salt dissolves in water. Resin regeneration

must then be performed.

First resin regeneration (ONLY 230459 model)

Regeneration must be activated with the usage of the manual regeneration button. Regeneration will

be done automatically. After it ﬁnishes, the device is ready to operate.

Operating cycles of the device

In serve the device is in the position of the ﬁrst operation cycle, i.e. water treatment. Water

ﬂows though the device. Raw water enters the container with resin through the

controller, ﬂows through the resin and is directed upwards, through a distribution

pipe, to the controller and further to the system.

BACKWASH

The device is in the position of the second operation cycle - anti-current rinse

(backwash). Raw water enters the container with the ﬁlter bed through an inlet valve and

is directed downwards with a central pipe. Water ﬂows through the resin, rinses it and

ﬂuffs it, and then is directed to sewage. In this cycle the controller shuts off water inlet

to the water system. Thanks to which the controller protects the water system against

the penetration of impurities from rinsing.

BRINE DRAW SLOW RINSE T

he device in the position of third operation cycle - regeneration with brine and slow

rinsing. Raw water with brine enters to the container with the ﬁlter bed through an inlet

valve. Flowing through the bed in the tank, it regenerates its ion exchange capacity. After

ﬂowing through the bed, water is directed to sewage. After all brine in the brine tank is

used up, the ion exchange bed is rinsed slowly with water, which guarantees thorough

rinsing brine and proper regeneration conditions. In this cycle the controller shuts off

water inlet to the water system. Thanks to which the controller protects the water

system against the penetration of impurities from rinsing.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 230442 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 1,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hendi 230442 Manual

Product: