Manual Hendi 230442 (page 5 of 144) (English, German, Dutch, French, Italian, Polish)

742508

Zoom out

Zoom in

1/144

Preparation for installation

After unpacking of the device, a power supply, a

2.5” wrench for the head ﬂange, 3/4” seals and 3/4”

connectors shall be taken out of the brine tank.

Only the special recesses in the housing shall be

used to lift and move the device around. The device

shall not be lifted by its electric cables or water

hoses due to damage that might occur.

Before installing, ensure that water mains pres-

sure is above 1.5 bar and below 6.0 bar. Shall the

pressure be higher, a reducing valve shall be in-

stalled upstream the device.

A location as close as possible to the water inlet of

a building shall be chosen (a water meter in case

of mains water supply or a hydrophore in case of

own water source/inlet) and in the vicinity of drain-

age. Moreover, permanent electric power supply is

necessary, therefore a socket must be near. The

surface of installation must be stable and must

withstand the weight of the device ﬁlled with water.

Ambient temperature in the selected installation

area shall never drop below 5°C, otherwise the

device may be permanently damaged. The devices

shall not be installed in rooms with excessive air

humidity. What is more, the selected area shall be

large enough to guarantee free access to the de-

vice, as it requires periodical reﬁlling of salt.

Installation

The connectors of the control head are marked as

IN (inlet) and OUT (outlet), looking from the front of

the control head: IN (inlet) on the right, OUT (out-

let) on the left. The seals and connectors provided

shall be placed/ﬁxed onto the connectors of the

control head. The water softener shall be connect-

ed to the system with ﬂexible hoses (not provided).

A mechanical ﬁlter shall be installed upstream the

softener, of at least 50 microns, in order to protect

the device against impurities.

A by-pass can be executed by means of regular

valves, as indicated in Fig. A. A turbine must be in-

stalled in a nipple ﬁxed onto the “OUT” connector

of the control head. Before installation, make sure

that the turbine rotates freely (e.g., by blowing air

into the water outlet). The device shall be installed

by means of materials intended for water installa-

tions. In case of any problems or doubts, contact

a qualiﬁed installation company or an authorized

service company.

Diagram of the device

Control head

Cover

Flange

Upper basket

Overflow elbow

Distrubution pipe

Resin

Lower basket

Brine valve pit

Brine valve

Cabinet

Salt

Container

Fig. A

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 230442 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 1,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hendi 230442 Manual

Product: