Manual Hendi 225165 (page 6 of 112) (English, German, Dutch, French, Italian, Polish)

741834

Zoom out

Zoom in

1/112

4. INSTRUCTIONS FOR THE INSTALLER

The following instructions are aimed at the quali-

ﬁ ed installer, to ensure that he carries out the in-

stallation, adjustment and maintenance operations

as correctly as possible and according to current

legal regulations. Any operation must be per-

formed with electrical power cut to the appliance.

Before using the appliance, carefully remove the

special adhesive ﬁ lm protecting the parts in stain-

less steel. Do not leave any glue residues on the

surfaces. If necessary, remove them at once, with

an appropriate solvent.

4.1 FITTING THE FEET

The feet are inside the appliance and must be se-

cured on the four threaded holes on the base. If

necessary, the height of the feet can be adjusted by

screwing or unscrewing.

4.2 POSITIONING

Position the appliance perfectly horizontally on

a table or similar support (the table or support

must be at least 85 cm above the ﬂ oor). Once you

have put the machine, it should not exceed height

of 1.60 meter from the ﬂ oor; position it at a dis-

tance of not less than 10 cm from the side and rear

walls, to enable natural ventilating air to circulate

freely around it. The appliance is ventilated through

speciﬁ c openings on the metal walls of the outer

housing, and ensures efﬁ ciency and long-life. For

this reason it is strictly forbidden to obstruct these

ventilation openings, even partially or for short

periods. Failure to observe this specific prohibi-

tion releases the manufacturer of the appliance

from all responsibility and immediately voids any

guarantee rights for the said appliance, because

its constructive conformity has been voluntarily

compromised. Furthermore, the appliance is not

suitable for embedding and for grouped positioning

with other identical appliances.

4.3 ELECTRICAL CONNECTION

The appliance must be connected to the electri-

cal mains according to current legal regulations.

Before making the connection, make sure of the

following:

• the voltage and frequency values of the power

supply system match the values on the „technical

data” plate afﬁ xed on the appliance;

• the limiting valve and the system are able to

support the appliance’s load (see the „technical

data” plate);

• the power supply system has an adequate earth

connection according to current legal regula-

tions;

• a omnipolar switch with minimum between-con-

tacts

aperture of the overvoltage category III

(4000 V), sized to the load and conforming to

current legal regulations, is ﬁ tted between the

appliance and the mains in the direct connection

to the mains;

• the omnipolar switch used for connection is easy

to reach when the appliance is installed;

• the yellow/green earth wire is not interrupted by

the switch;

• the power supply, when the appliance is operat-

ing, must not deviate from the rated voltage value

by ±10%;

• make sure that after inserting the power supply

cord into the terminal block it does not come into

contact with any of the cooking range’s hot parts.

• if the supply cable is damaged then it must be

replaced by the manufacturer or by your techni-

cal

support or by a qualified person to avoid any

risk.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 225165 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 8,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hendi 225165 Manual

Product: