In this mode the ltration is switched on in accordance with timers that allow adjustment of the start and end times of the ltration. Timers always
operate daily, in cycles of 24 hours.
To set the ON/OFF times (conguration of up to 3 times possible), use the up/down keys in the timer line that you want to change (1-3).
Open the start time input eld for the selected timer using the plus/minus keys. Set the time with plus/minus keys. Use the up key to scroll up to the
minutes input eld and set this using plus/minus keys. To conrm press OK and to cancel press return/escape. To set the OFF timer, proceed in the
same way.
See section Filter Cleaning below.
7.47.4 Smart*: This mode is based on the automatic or timer mode, with its 3 ltration intervals, but with adjustment of the ltration times as a function
of the water temperature. Two temperature parameters are provided for this: the maximum temperature, above which the ltration times will be those
set by the timers, and the minimum temperature, below which the ltration time will be reduced to 5 minutes, which is the minimum operating time.
Between these 2 temperatures the ltration times increase linearly. Use the plus/minus keys to set the desired minimum and maximum temperatures.
There is the option of activating the antifreeze mode which sets the ltration to run continuously if the water temperature is below 2 °C.
To set the ON/OFF times (conguration of up to 3 times possible), follow the instructions for the Automatic Mode.
See section Filter Cleaning below.
* N.B.: Mode only visible when the option to use temperature probe and/or heating is activated in the “Installer Menu”.
7.57.5 Filter cleaning mode (and pool cleaning by suction): From this menu (accessible from any Filtration Mode) a backwash cleaning of the sand lter
can easily be carried out. Activating this menu from any ltration mode (Manual, Automatic, Smart), will disconnect the electrolysis/hydrolysis cell.
Then proceed as follows:
• Turn the lter pump OFF using the plus/minus keys.
• Place the ltration pump valve in the backwash cleaning position.
• Turn the ltration pump back ON. You can check the duration of the backwash cleaning by looking at the clock on the screen. Make sure an
adequate and complete backwash of your lter has been carried out.
• When you have nished the backwash cleaning, again turn the ltration pump OFF and put the valve back in the ltering position. If you wish, you
can now perform a rinse cycle.
• Proceed in the same way as for backwash cleaning, this time placing the ltration pump valve in the rinsing position.
• When exiting the Filter Cleaning menu using the return/escape key, the system will revert back to the mode programmed previously.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Hayward Aqua Rite Flo Advanced at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Hayward Aqua Rite Flo Advanced in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.
The manual is 94.1 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.