295355
30
Zoom out
Zoom in
Previous page
1/40
Next page
5. Depress
the
exposure
release
button
fully
to make
the
exposure
and
trigger
the flash.
The
control
circuits
in
the flash
unit cut
the flash
when
the
exposure
is
cor-
rect.
Ifthe flash
was
powerful
enough
to produce
a cor-
rect
exposure
and
did not
use
up
all the
energy
the
flash
symbol
stays
on. 0n
the other
hand
if so
much
power
had
been used
that
the remainder
was insuffi-
cient for
a correct
exposure,
the flash
symbol
turns off
while
the flash
unit is recharging
and lights
up again
when
it is fully
recharged.
T1IIRNINGS:
The
sign "Hi
FLASH"
appears
on the
display
when
the
flash
was
too
strong,
e.g. ifthe
flash-to-subject
distance
is
too short,
the
camera
aperture
too large,
the film
too
fast
or any
combination
of these.
The
remedies
are to
move
the flash
away from
the
subject
(use
a lens
with
longer
focal length),
reduce
the
aperture,
change
to a
slower film.
The
sign
"Lo
FLASH"
appears
when
the flash
was insufficient
to give
a correct
exposure,
e.g. if
the
flash-to-subject
distance
is too
long,
the
aperture is
too
small,
the film
too
slow. The
remedies
are to lessen
flash-
to-subject
distance,
increase
aperture
or
to use faster
film.lt
also appears
at
shutter
speeds
faster
than l/90
s
when
the flash
triggering
was
disabled.
Both
warnings
appear
together
with
a
flashing
backlight
display for
two
seconds
after
the flash
exposure.
6.
Rewind
the
camera
to cock
the
shutter
and advance
the film
to the next
frame.
The flash
unit should
be
set
for
manual
control
(see
the
flash
unit instructions).
Functions:
'
Exposure
with pre-set
aperture
and shutter
speed
determined
by
the
operating mode.
'
Viewfinder
indication
when
the flash
unit is charged
and ready
to flash.
'
Viewfinder
warning
at over-
and
under
exposure
and
disabled fl
ash triggering.
Suggested
procedur-e:
.'tiiffitiiriffii'ii
l. Attach
and connect
the flash
according
to the flash
manual.
With
the Hasselblad
D-Flash
40
connect
the
TTL
cable between
the dedicated
flash
socket
on the
camera
body
and the
TTL
socket
on the flash
unit.
2.
Set the flash
unit to Manual
or corresponding
mode
and
switch it
on.
When
the flash
unit is
charged
and
ready
to flash,
the
green flash
symbol lights
up in
the
viewfinder.
3.
Estimate
the flash-to-subject
distance
or measure
it
by
focusing
the lens
and reading
the
distance from
the fo-
cusing
scale.
4. Determine
the
aperture
setting
using
the aperture
cal-
culator
on the flash
unit or
the
guide
number
(see
the
flash
unit manual).
5. Depress
the exposure
release
or the pre-release
button
to
the
pressure
point
to
activate
the camera
that oper-
ates in
the chosen
mode.
The
display
indicates
the
aperture
setting,
the shutter
speed,
mode
and flash
in-
formation.
6.
Depress
the
exposure release
button fully
to
release
the
exposure
and
trigger
the flash.ln
Manual
mode
the
flash
normally
uses allthe
accumulated
power.
7. The
flash
symbol
therefore
is
turned
off and is
dis-
played
again
when
the
unit has re-charged
sufficiently.
WARNINGS:
The
sign
"Hi
FLASH"
appears
on
the display
when
the
flash
was
too strong,
e.g. if
the flash-to-subject
dis-
29
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hasselblad 202 fa at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hasselblad 202 fa in the language / languages: English as an attachment in your email.

The manual is 4,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info