295355
29
Zoom out
Zoom in
Previous page
1/40
Next page
4.
Depress the exposure button to the
pressure point. The
camera
works according to the selected mode. When
the
exposure button is depressed to the
pressure point
the display appearance is according to that
mode
and
for
the described
flash indications.
5. Depress the exposure button
fully
to
make
the expo-
sure and trigger
the flash. The control circuits in the
camera cut
the flash when
the exposure
is correct.
Release the exposure button.
If the flash was powerful
enough to
produce
a correct exposure but
did not
use
up
all
the
power the flash symbol stays on and the dis-
play returns to its normal appearance.0n the other
hand if so
much power had
been used that the
remain-
der was insufficient
for
a correct exposure, the
flash
symbol turns offwhile
the flash
unit
is recharging and
lights up again when
it is fully recharged.
WARNINGS;
The
sign
"Hi
FLASH" appears
on the display
when the
flash was too strong, e.g.
if
the
flash-to-subject
dis-
tance was too short, the camera aperture too
large,
the
film
too
fast or any combination of these. The reme-
dies are to
move
the
flash
away
from
the subject
(use
a
lens with longer focal
length), reduce
the aperture or-
change
to a slower film. The sign
"Lo
FLASH'appears
when the flash was insufficient to give a correct expo-
sure, e.g.
if
the
flash-to-subject distance is
too
long, the
aperture
is
too small, the
film
too slow.
The remedies
are to
lessen flash-to-subject distance, increase the
aperture
or
use
faster film. It also appears at shutter
speeds
faster
than
l/90
s when the
flash
triggering was
disabled and the exposure
was made.ln
both
cases the
suggested
remedies
could be combined
in
any
desired
way.
Both
warnings appear
for
two seconds after the
flash exposure together with a flashing triangle and
backlighting,
appearing in both the internal display as
28
well
as
in the display backlighting window on the out-
side of the camera.
6. Rewind the camera to cock the
shutter
and advance
the film to the next frame.
The flash unit should be set for its own built in automatic
control
(see
the
flash unit instructions)
Functions:
'
Automatic
exposure control through the built-in sys-
tem in the flash unit.
'
Exposure with
pre-set
aperture and shutter speed de-
termined by the selected operating
mode.
'
Viewfinder indication
when the
flash
unit
is
charged
and ready to flash.
'
Viewfinder warning at over- and under exposure and
disabled
fl
ash
triggering.
Suggested
procedure:
t:t:t:::::::t::tt:t:::.:t:::::t:t::::t:::::::::t::tt:t::.tt:t:::::t:t::.
,tl:2fj:,,:*::,|,,1:E:#,'
L Attach and connect the flash according to the Flash
Manual. With
the
Hasselblad D-Flash 40,
connect the
TTL
cable between the dedicated
flash
socket
in
the
camera body and the
TTL
socket
in
the
flash
unit.
2. When
the
flash
unit
is
charged and
ready
to
flash,
the
green flash
symbol
lights up in
the
viewfinder.
3. Select and
pre-set
the
lens
aperture
for
the desired
depth-of-field.
or
set the
aperture
according to
the'flash
illumination
range'chart
corresponding with the desired distance.
4. Depress
the exposure
release
or the
pre-release
button
to the
pressure point
to start the camera.
The
camera
operates
in
the selected
mode
and the display shows
the corresponding indications.
www.orphancameras.com
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hasselblad 202 fa at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hasselblad 202 fa in the language / languages: English as an attachment in your email.

The manual is 4,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info