624014

Hartke HA5500 Manual

9
Zoom out
Zoom in
Previous page
1/72
Next page
Guided Tour - Model 3500/5500 Front Panel
6. Compression control - This determines the amount of compression (peak
signal reduction) by simultaneously adjusting both threshold and compres-
sion ratio (which ranges from 2:1 to infinity [limiting]). At the fully coun-
terclockwise “Off” position, the circuitry is bypassed and no compression is
applied (the knob clicks when set to the “Off” position). As the knob is raised
clockwise, (at settings from “1” to “∞”) increasing amounts of compression are
applied. For more information, see the “About Compression” section on page
12 of this manual.
7. Graphic Equalizer In/Out switch - When pressed in (the “In” position), the
Model 3500/5500’s graphic equalizer circuitry (as described in #8 below) is
operational. When pressed out (the “Out” position), it is bypassed. The provi-
sion of this switch allows you to set up a custom equalization curve (an equal-
ization “preset”) with the graphic EQ sliders, which can then be activated with
the press of a single button.
8. Graphic Equalizer - These sliders allow you to “draw” the tonal response
of the system by adding 15 dB of boost or attenuation to ten different nar-
row-band frequency areas (30 Hz, 64 Hz, 125 Hz, 250 Hz, 500 Hz, 1 kHz, 2
kHz, 3 kHz, 5 kHz, and 8 kHz), affecting the main output signal of the Model
3500/5500. When a slider is at its center detented (“0”) position, the selected
frequency area is unaffected (it is said to be flat). When a slider is moved up
(above the “0” position, towards the “+15” position), the selected frequency
area is boosted, and when it is moved down (below the “0” position, towards
the “-15” position), the selected frequency area is attenuated. For more infor-
mation, see the “About Equalization” section on pages 10 - 11 of this manual.
9. Contour Low Pass control - This acts as a broad-band low frequency
equalizer, providing 18 dB of boost or attenuation at 100 Hz. You should
generally adjust this control (and the Contour High Pass control, described
in #10 below) prior to “fine-tuning” the system with the graphic equalizer (as
described in #8 above). For more information, see the “About Equalization”
section on pages 10 - 11 of this manual.
10. Contour High Pass control - This acts as a broad-band high frequency
equalizer, providing 18 dB of boost or attenuation at 10 kHz. You should
generally adjust this control (and the Contour Low Pass control, described
in #9 above) prior to “fine-tuning” the system with the graphic equalizer (as
described in #8 above). For more information, see the “About Equalization”
section on pages 10 - 11 of this manual.
11. Master Volume control - This is the overall volume control. For best
signal-to-noise ratio, keep the output of your bass at or near maximum and
adjust the amp’s Master Volume to the desired level.
12. Power LED - Lights whenever the Model 3500/5500 is powered on.
13. Power switch - Use this to power the Model 3500/5500 on or off.
ENGLISH
5
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hartke HA5500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hartke HA5500 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info