624014

Hartke HA5500 Manual

11
Zoom out
Zoom in
Previous page
1/72
Next page
Guided Tour - 3500/5500 Rear Panel
6. Effect Return jack - Use this 1/4” unbalanced jack to return low impedance
(600 ohm) signal to the Model 3500/5500 from a professional outboard effects
processor.*
7. Balance control - Use this to adjust the relative amount of Effect Send (dry)
versus Effect Return (wet) signal being routed to the Model 3500/5500 speaker
outputs. At the center-detented “0” position, equal amounts of Send and Return
signal are routed. At its fully counterclockwise (“Send”) position, no signal from a
connected effects processor(s) is added to the main output. At its fully clockwise
(“Return”) position, the only signal you hear is that coming from a connected out-
board effects processor(s). If your outboard effects processor has an adjustable
wet/dry control, we recommend that you set the Balance knob to its fully clock-
wise (“Return”) position and use the effects processor’s wet/dry control to adjust
the relative mix. Alternatively, you can set the effects processor to output fully
“wet” signal and use the Model 3500/5500 Balance knob to adjust the relative
mix of dry vs. wet signal
8. Direct Out Post/Pre switch - When pressed in (the “Pre” position), signal is
routed to the Direct Out jack prior to the Model 3500/5500 ten-band graphic
equalizer (but after the compression circuitry and Contour controls). When out
(the “Post” position), signal is routed to the Direct Out jack after all compression
and EQ circuitry (both ten-band graphic and Contour).** Use the “Pre” position
when you want the console engineer to have control over equalizing your bass
signal; use the “Post” position when you want to use the front panel ten-band
graphic equalizer to equalize your bass signal before sending it to the console.
9. Direct Out Normal/Ground Lift switch - When pressed in (the “Gnd. Lift” posi-
tion), pin 1 is removed from the chassis. This should be used only when a ground
loop hum or buzz is heard; otherwise, leave it in the out (“Normal”) position.
10. Direct Out jack - Use this electronically balanced XLR jack to route signal
from the Model 3500/5500 to a professional mixing console or as a tap to a main
PA system via a mic input on the console. The signal output from this jack is low
impedance (100 ohm) with an output level of approximately -30 to -20 dB. You
can also use the Direct Out jack to route signal to an external amplifier with a -10
dB input sensitivity.
* In-line effects (such as footpedals) intended for low signal levels should be placed
between the bass and the amplifier Input and not connected with the Effect Send and
Return jacks.
** Note that the settings of the ten-band graphic equalizer will affect a “Post” Direct
Out signal regardless of the position of the front panel In/Out switch.
ENGLISH
7
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hartke HA5500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hartke HA5500 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info