the code being sent so that it is facing the
IR Transmitter Window b on the
AVR 520 remote “head-to-head.” The
remotes should be between one and three
inches apart.
2. Select the button on the remote that you
wish to use as the device selector for the
codes about to be entered. This may be any
of the
Input Selectors e.
3. Press the
Input Selector e button
chosen and the
Learn Button h at the
same time. Hold these buttons until the
Program/SPL Indicator c flashes amber
and the light under the device selector but-
ton turns red. Release the buttons.
4. Press the button on the AVR 520 remote
that you wish to program. Note that the
Program/SPL Indicator c will stop
flashing.
5. Within five seconds, press and hold the but-
ton on the original remote that you wish to
“teach” into the AVR 520 remote. When the
Program/SPL Indicator c turns green
three times, release the button. Note that
the Program Indicator will then begin to
flash amber again.
NOTE: If the Program/SPL Indicator c
turns red during Step 5 or 6, the program-
ming was not successful. Repeat the steps to
see if the code will “take.”
6. Repeat Steps 4 though 6 for each button on
the source remote that you wish to transfer
to the AVR 520 remote.
7. Once all codes have been transferred from
the original source remote to the AVR 520
remote, press the
Learn Button h.
8. Repeat Steps 1 through 7 for any additional
remotes you wish to “teach” into the
AVR 520 Remote.
Erasing Learned Codes
The AVR 520’s remote allows you to remove or
erase, the code learned into a single button for a
single device, to remove or erase the code set for
all the codes that have been programmed into
specific device buttons, or to erase all commands
that have been learned to all devices.
To erase a single learned code from within a sin-
gle device’s settings, follow these steps:
1. Press and hold both the
Input Selector
efg within which the individual but-
ton to be erased has been programmed and
the
Learn Button h.
2. When the red LED under the
Input Selector
turns red and the Program/SPL Indicator
c flashes amber, release the buttons.
3. Press and release the
Input Selector
efg again for the device within
which the individual button to be erased has
been programmed.
4. Press the
7 Button r four times.
5. Press and release the individual button for
which the code is to be erased.The
Program/SPL Indicator c will blink
green two times and then return to amber.
6. To erase other buttons within the same
device, press them as noted in Step 5.
7. When all buttons to be erased have been
pressed, press the
Learn Button h to
complete the process.
To erase all codes within a single device, follow
these steps:
1. Press and hold both the
Input Selector
efg for which you wish to erase the
codes and the
Learn Button h.
2. When the red LED under the
Input Selector
turns red and the Program/SPL Indicator
c flashes amber, release the buttons.
3. Press and release the
Input Selector
efg again for the device whose
codes you wish to erase.
4. Press the 8 button
r four times.
5. The
Program/SPL Indicator c will turn
off and the red light under the
Input
Selector
will flash on and off once to indi-
cate that the codes have been erased.
To erase all codes that have been programmed
to all devices in the remote, follow these steps:
1. Press any
Input Selector efg for
which you wish to erase the codes and also
the
Learn Button h.
2. When the red LED under the
Input Selector
turns red and the Program/SPL Indicator
c flashes amber, release the buttons.
3. Press and release the
Input Selector
efg again for the device whose
codes you wish to erase.
4. Press the
9 Button r four times.
5. The
Program/SPL Indicator c will turn
off and the red light under the
Input
Selector
will flash on and off once to
indicate that the codes have been erased.
Macro Programming
Macros enable you to easily repeat frequently
used combinations of commands with the press
of a single button on the AVR 520’s remote
control. Once programmed, a macro will send
out up to 19 different remote codes in a prede-
termined sequential order enabling you to auto-
mate the process of turning on your system,
changing devices, or other common tasks. The
AVR 520’s remote can store up to five separate
macro command sequences: one that is
associated with the
Power On Button a
and four more that are accessed by pressing the
Macro Buttons .
1. Press the
Mute Button and the
Macro Button to be programmed or
the
Power On Button a at the same
time. Note that an
Input Selector will
light red, and the
Program/SPL Indicator
c will flash amber.
2. Enter the steps for the macro sequence by
pressing the button for the actual command
step. Although the macro may contain up to
19 steps, each button press, including those
used to change devices, counts as a step.
The
Program/SPL Indicator c will flash
green to confirm each button press as you
enter commands.
NOTE: While entering commands for Power
On/Off of any device during a macro sequence,
press the
Mute Button .DONOT press the
actual Power button.
3. When all the steps have been entered,
press the
Sleep Button j to enter the
commands. The red light under the
Input
Selectors
ef will blink and then
turn off.
