502541
33
Zoom out
Zoom in
Previous page
1/76
Next page
33
INITIAL SETUP
Before you begin enjoying your new receiver, a few adjustments should
be made to configure the AVR 347 to match your actual system.
Make sure that you have connected a video display to one of the
video
monitor outputs on the receiver. When you turn on your display and the
AVR, you should see a blue screen. A message may appear briefly at
the bottom of the screen. This message is part of the on-screen display
system, and is referred to as the “semi-OSD”. The semi-OSD is activated
any time you send a command to the AVR, and any time the AVR
detects a change in the incoming signal. Semi-OSD messages are
overlaid on top of any video signal, so that you may continue to watch
your program while making adjustments to the AVR.
Although it’s possible to configure the AVR using only the remote and
the semi-OSD messages, we recommend that you use the full-screen
menu system, known as the “full OSD”.
Using the On-Screen Menu System
The full-OSD system is accessed by pressing the OSD Button on the
remote. See Figure 47. While the full-OSD system is in use, it isn’t
possible to see any video programming. In addition, an OSD ON
message will appear on the front panel of the receiver to remind
you to use a video display.
Figure 47 – Navigation Buttons
NOTE: The / and Set Buttons on the front panel have no
effect on the OSD system.
The OSD system consists of six main menus: Input Setup, Surround
Setup, Speaker Setup, Multiroom Setup, Video Setup and System Setup.
Navigation tabs for each menu appear on the left side of the screen.
When you first press the OSD Button, the Input Setup menu will be visi-
ble (see Figure 48), since its tab is at the top of the screen. However,
you must press the Set Button to select the Input Setup menu so that
you can make any necessary adjustments. If you wish to select another
menu, use the
/
¤
Buttons to highlight the tab for the desired menu,
and press the Set Button to select it.
Figure 48 – OSD System
When you first select a menu, the first setting line will be highlighted
(see Figure 49).
Figure 49 – Input Setup Menu
If you wish to change that setting, press the Set Button. Although the
setting name will remain highlighted, the value will appear in blue type
with arrows to the left and right, indicating that you may use the
/
Buttons to scroll through the available values. See Figure 50. When the
desired value appears, press the Set Button to select it.
Figure 50 – Changing a Setting
Use the
/
¤
Buttons to navigate to other settings within the menu.
When you have finished making all adjustments in that menu, press the
Button to return to the navigation tabs, and then use the
/
¤
Buttons to select the tab for another menu.
We recommend that most users follow the instructions in this INITIAL
SETUP section to configure a basic home theater system. You may
return to these menus at any time to make additional adjustments.
Thanks to the EzSet/EQ system, most of the menu adjustments may
be saved until you have become more familiar with the AVR, and are
therefore described in the Advanced Functions section.
AVR347 om.qxd 7/10/07 11:01 AM Page 33
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR 347 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 347 in the language / languages: English as an attachment in your email.

The manual is 7,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 347

Harman Kardon AVR 347 User Manual - German - 64 pages

Harman Kardon AVR 347 User Manual - Dutch - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info