502541

Harman Kardon AVR 347 Manual

35
Zoom out
Zoom in
Previous page
1/76
Next page
35
INITIAL SETUP
surround back speaker to the left Surround Back Speaker Output,
and then configure the surround back speaker manually, as
described in the Advanced Functions section. However, we do
not recommend the 6.1-channel configuration.
If you have forgotten to plug in the EzSet/EQ microphone, the warning
screen shown in Figure 55 will appear as a reminder.
Figure 55 – EzSet/EQ: Warning to Plug in Microphone
NOTE: As shown in Figures 53, 54 and 56 –59, while
EzSet/EQ is in progress a Cancel setting is highlighted. You
may interrupt EzSet/EQ at any time by simply pressing the
Set Button.
What EzSet/EQ Does
EzSet/EQ will send test signals to the various speakers and perform
the measurements described in this section, adjusting the AVR 347’s
settings to match EzSet/EQ’s internal references.
Set Master Volume Level: EzSet/EQ sends test tones to the front
speakers and adjusts the system’s volume level to enable it to take the
remaining measurements correctly. EzSet/EQ uses the left front speaker
to set the master volume level, and then it proceeds directly to measur-
ing the speaker output levels.
Speaker Level: During this test, EzSet/EQ ensures that all speakers
sound equally loud at the listening position. During a surround sound
presentation it is common for the surround channels to sound less
prominent, or not to be used at all at times. By setting the baseline
channel levels correctly, the AVR behaves as a blank canvas for the
movie director to create special effects.
A screen similar to the one shown in Figure 56 will appear, with the
speaker position changing as EzSet/EQ measures the levels for each
speaker. You may occasionally hear EzSet/EQ send a tone back to the
front left speaker. This enables EzSet/EQ to compare the level of the
speaker being measured to the reference level it set for the front left
speaker.
Figure 56 – EzSet/EQ: Speaker Level Test
If at any time the test tone is not heard from the speaker indicated on
screen, press the Set Button to stop EzSet/EQ. Turn off the AVR using
the Master Power Switch and check your speaker connections. Make
sure all wires are connected to the correct speakers and Speaker
Outputs on the AVR, and that you have observed the correct polarity
(+ terminals connected to + terminals, and – terminals connected to
– terminals).
NOTE: EzSet/EQ can detect only the presence of a speaker,
not its location within the room. If your speakers are not placed
reasonably close to the positions shown in the Speaker
Placement Section on page 23, EzSet/EQ may not be able
to perform this test correctly.
If EzSet/EQ detects only one speaker in a pair (e.g., surround back left
but no surround back right or no main speakers), it will generate an
error and stop. If that happens, check that you have placed your speakers
in their correct locations, and that you have wired each speaker to its
correct set of speaker terminals.
Speaker Distance: During this test, EzSet/EQ measures the distance
from each speaker to the listening position. If the speakers are placed
at different distances from the listener, the sound from speakers placed
closer needs to be delayed so that it reaches the listener at the same
time as the sounds from the other speakers. This preserves the clarity
and directionality of surround sound presentations. During the Speaker
Distance test a screen similar to the one shown in Figure 57 will appear.
The speaker position will change as EzSet/EQ measures the distance
for each speaker.
Figure 57 – EzSet/EQ: Speaker Distance Test
NOTE: The AVR 347 is also capable of setting a different type
of delay, called A/V Sync Delay. A/V Sync Delay is used to
compensate for lip sync problems that may occur when a video
AVR347 om.qxd 7/10/07 11:01 AM Page 35
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR 347 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 347 in the language / languages: English as an attachment in your email.

The manual is 7,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 347

Harman Kardon AVR 347 User Manual - German - 64 pages

Harman Kardon AVR 347 User Manual - Dutch - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info