502541
32
Zoom out
Zoom in
Previous page
1/76
Next page
32
32
INSTALLATION
3. Connect an external amplifier to the Surround Back/Multiroom
Preamp Outputs. See Figure 42.
Figure 42 – Surround Back/Multiroom Preamp Outputs
This method may be used when it is more important to distribute
audio to additional rooms than to have a full 7.1-channel system in
the main listening area, as it is still necessary to assign the surround
back amplifier channels to the remote zone, limiting the main system to
5.1 channels. This method also requires you to provide an additional
component, that is, the amplifier. However, this method may be used
to increase the number of remote rooms in the system when you are
also using the other options for connecting a multiroom system.
4. Connect an A-BUS hub or other A-BUS components to the A-BUS
Port. See Figure 43.
Figure 43 – A-BUS Port
Use Category 5/5e cable as described in the instructions for your
A-BUS components. The A-BUS system may carry the audio signal
to the remote components, while receiving IR control codes, depend-
ing on the capabilities of your A-BUS components. If you connect
a hub to the AVR 347, you may distribute audio to many remote
rooms. Visit our Web site at www.harmankardon.com for information
on our available hubs, the ABH 4 and ABH 4000, and amplified
in-wall modules, the AB 1 and AB 2.
In addition to the audio signal, you will usually wish to connect an IR
control device to the AVR 347’s Multiroom IR Input so that listeners in
the remote room may turn the multiroom system on or off, select a
source input, control the source device connected to that input and
adjust the volume in the remote zone. As mentioned above, an A-BUS
system does not require a separate IR control connection.
By using external multichannel amplifiers and A-BUS hubs, it’s possible
to construct a system that distributes audio to many rooms throughout
your home.
NOTE: Only analog audio sources are available to the multiroom
system.
Step Eleven – Turn On the AVR 347
Two steps are required the first time you turn on the AVR 347.
1. Gently press the Master Power Switch until the word OFF is no longer
visible. The Power Indicator above the two power switches should
light up in amber, indicating that the AVR is in Standby mode and is
ready to be turned on. See Figure 44. Normally, you may leave the
Master Power Switch in the ON position, even when the receiver is
not being used.
Figure 44 – Power Switches
2. There are several ways in which the AVR 347 may be turned on from
Standby mode.
a) Press the Standby/On Switch on the front panel. See Figure 44.
b) Press the Source Select Button on the front panel. See Figure 45.
Figure 45 – Source Select Button
c) Using the remote, press any one of these buttons: AVR, DVD/CD,
TAPE/The Bridge, HDMI 1/2, VID1, VID2, VID3, VID4, XM, AM/FM
or 6/8CH. See Figure 46.
Figure 46 – AVR and Input Selectors
NOTE: Any time you press one of the Input Selectors on the
remote (i.e., DVD/CD, TAPE/The Bridge, HDMI 1/HDMI 2, VID1,
VID2, VID3 or VID4), the remote will switch modes so that it will
only transmit the codes programmed to operate that device. In
order to control the receiver, press the AVR button to return the
remote to AVR mode.
AVR347 om.qxd 7/10/07 11:01 AM Page 32
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR 347 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 347 in the language / languages: English as an attachment in your email.

The manual is 7,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 347

Harman Kardon AVR 347 User Manual - German - 64 pages

Harman Kardon AVR 347 User Manual - Dutch - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info