626612
12
Zoom out
Zoom in
Previous page
1/213
Next page
Introduction
HA<O> Model XE-1 Basic Features Guide
2
2. Plug the female end of the Connector Cable into the receptacle on the back
lower left corner of the Leslie Speaker.
3. Plug the male end of the Connector Cable into the 11-pin Leslie socket found
on the Accessory Panel of the XE-1.
Both the Leslie connections are "keyed,” that is, each connection contains a notch which
insures that the pins properly match up.
IMPORTANT NOTE: The 11-pin Leslie socket on your XE-1 allows you to plug directly into
many standard 1-, 2- and 3-channel Leslie Speaker cabinets. Some current models: 303,
723, 914. However, it should be noted that when plugging the XE-1 into a single-channel
Leslie cabinet such as a 122XB, only the Drawbars will sound through the Leslie. For this
reason, we recommend that the XE-1 normally be used with a multi-channel Leslie
Speaker.
IMPORTANT NOTE: To connect the XE-1 to a Leslie Speaker having a different pin
configuration such as an older 6-pin 122 or 147, or a 9-pin cabinet such as the 900 series,
760 or 770 cabinets, you will require an adapter kit and/or Connector Cable. Contact your
Hammond Dealer for more information regarding which adapter kit and/or cable you may
need.
Connecting a Foot Switch
You can connect an optional foot switch such as the Hammond model FS-9H foot switch to your
XE-1. Simply plug the foot switch plug into the jack marked "FOOT SW" on the back of the XE-1.
NOTE: In order to insure proper operation of the Foot Switch, be sure to connect it when the XE-1 “OFF.”
Connecting an EXP-100 Series Expression Pedal
If you wish to use a Hammond EXP-100 Series Expression Pedal, a special DIN-type jack is
provided on the Accessory Panel on the back of the XE-1. Simply insert the plug from the EXP-
100 into this jack as shown below.
NOTE: ONLY the EXP-100 plug should be inserted into this jack.
Connecting an XPK-100 MIDI Pedalboard
If you wish to use a Hammond XPK-100 MIDI Pedalboard, use a MIDI cable to connect the MIDI
OUT port from the XPK-100 to the MIDI IN 1 port of the XE-1.
NOTE: For best results, the XPK-100 Control Channel should be set to “16.” Please consult your XPK-
100 Quick Features Guide for instructions on how to do this.
Connecting the XLK-1 Additional Keyboard
If you wish to use a Hammond XLK-1 keyboard:
1. Use a MIDI cable to connect the MIDI OUT port from the XLK-1 to the MIDI IN
1 port of the XE-1.
2. Connect the DC Power Supply for the XLK-1 from the DC OUT of the XE-1 to
the DC IN jack on the XLK-1.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hammond XE-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hammond XE-1 in the language / languages: Dutch as an attachment in your email.

The manual is 1,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info