626612

Hammond XE-1 Manual

11
Zoom out
Zoom in
Previous page
1/213
Next page
Introduction
HA<O> Model XE-1 Basic Features Guide
1
INTRODUCTION
♦ Basic Hook-Up
All connections except the Headphone Jack are found on the Accessory Panel on the back of the
XE-1. The Headphone Jack is located on the front of the instrument just below the Disk Drive
Slot. Please refer to the diagram on page 4 to see the various hookups described in this section.
Refer to the numbered bullets before each paragraph and on the diagram.
• A.C. Power
Your Hammond XE-1 is shipped from the factory set for 120 V.A.C. power. To connect the XE-1
to A.C. power:
1. Locate the A.C. Power Cord that came with your XE-1.
2. Plug the female end of the Power Cord into the receptacle on the XE-1
marked, “AC IN.”
3. Plug the other end of the Power Cord into an A.C. power outlet.
Audio Connections
Your XE-1 is equipped with a high-quality built-in sound system. However, it may be desired to
hear the sounds produced by the XE-1 through external sound sources. You can either:
1. Connect the XE-1 to an amplifier, or;
2. Connect the XE-1 to a Leslie Speaker cabinet.
‚ Connecting to an Amplifier
1. Use two audio cables with
1
/
4
" plugs on both ends of each cable.
2. Connect one end of each of the audio cables to the audio output connectors on the
back of the XE-1.
NOTE: At this point it is assumed that you are using a keyboard or guitar amplifier that has
1
/
4
"
phono plug inputs. We assume this since this is the most common type of connector used on
these types of amplifiers.
3. Connect the other ends of each cable to the female
1
/
4
" audio input
connectors of your amplifier.
If your amplifier has only a single (1) female
1
/
4
" phono plug audio input, you can connect
one end of one cable to the L/MONO audio output connector on the XE-1, and the other
end to the female
1
/
4
" audio input connector of your amplifier.
ƒ Connecting a Leslie Speaker (11-pin)
If you wish to use a Leslie Speaker with your XE-1, the Leslie Speaker should be connected
before turning the power "ON". To do this:
1. Locate the Leslie Connector Cable.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hammond XE-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hammond XE-1 in the language / languages: Dutch as an attachment in your email.

The manual is 1,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info