665711

Gys TIG 300 DC Manual

24
Zoom out
Zoom in
Previous page
1/88
Next page
24
TIG 220 DC / 300 DC
EN
Connection
The TIG 300 DC is equipped with a female socket for a remote control.
The specic 7 pin male plug (option ref.045699) enables connection to the different types of manual remote control or foot pedal. For the cabling
layout, please see the diagram below.
REMOTE CONTROL TYPE Wire description Pin
CONNECT-5
Foot pedal Manual remote control
5V A
Cursor B
Common/Earth C
Switch D
AUTO-DETECT E
ARC ON F
REG I G
Operating :
• Manual remote control (option ref. 045675)
The remote control enables the variation of current from 50% to 100% of the set intensity. In this conguration, all modes and functions of the
machine are accessible and can be set.
• Pedal (option ref. 045682) :
The pedal control enables variation of the current from the minimum set current to a 100% of the set intensity.
In TIG mode, the machine will only operate in two-stage welding (2T mode). The upslope and downslope are not automatic, and are controlled by
the User with the foot pedal.
• Connect 5 - automaton mode:
This mode enables to pilot the TIG 300 DC from a console or from an automaton due to 5 pre-saved programs.
As the foot pedal, the «Switch (D)» enables to start or stop welding according to the choosen cycle. The voltage value for the «slider (B)» matches
a program or the actual statut.
This voltage must be between 0 and 5V (step of 0.5V) which is linked to a program reminder:
- Actual status : 0 - 0.7V
- Program 1 : 0.8- 1.5V
- Program 2 : 1.6 - 2.2V
- Program 3 : 2.3 - 3.0V
- Program 4 : 3.0 - 3.7V
- Program 5 : 3.8 - 4.5V
An additional potentiometer enables to change the current (+/- 15%) either whilst welding or not. The information ARC ON (arc presence) enables
the automaton to synchonise itself (Pull Up 100k entry, automaton side). Put the pin AUTO_DETECT to the earth enables to start the product
without going through the window where you can select the type of remote control used.
The 5 programs loaded correspond to the frist 5 saved programs (P1 to P5).
Additional explanations are avialable on our website
(https://goo.gl/i146Ma)
.
COOLING UNIT
TIG 220 DC
WCU0.5kW_A
P 1L/min = 500W
Capacity = 1.5 L
U1 = 185V - 265V
When working within the 185V-265V power supply range, the cooling unit is controlled by the welding
machine,
When working within the 85V-185V power supply range, the cooling unit is always switched off.
WCU1kW_A
P 1L/min = 1000W
Capacity = 3 L
U1 = 85V - 265V
The cooling unit is controlled by the welding machine throughout the 85V-265V power supply range.
TIG 300 DC
WCU1kW_B
P 1L/min = 1000W
Capacity = 3 L
U1 = 400V +/- 15%
The cooling unit is controlled by the welding machine throughout the power supply range.
This machine may be connected to a cooling system for the cooling of the water torch. In the OPTION menu, this cooling unit system can be deac-
tivated.
A 3 second press on the
MEM
PROG
button allows access to the cooling unit system menu.
Make sure that the cooling unit is turned off before disconnecting the inlet and outlet hoses for torch liquid.
The coolant is harmful and irritates the eyesm the mucus membranes and the skin. Hot liquid may cause burns.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys TIG 300 DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys TIG 300 DC in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info